Volkswagen EuroVan Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Volkswagen EuroVan Brake Drum Replacement is $305 with $192 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1994 Volkswagen EuroVanL5-2.5L	Service typeBrake Drum Replacement	Estimate$959.91	Shop/Dealer Price$1141.77 - $1617.61
1992 Volkswagen EuroVanL5-2.5L	Service typeBrake Drum Replacement	Estimate$907.41	Shop/Dealer Price$1090.33 - $1566.96
1999 Volkswagen EuroVanV6-2.8L	Service typeBrake Drum Replacement	Estimate$575.79	Shop/Dealer Price$703.26 - $1058.62
1997 Volkswagen EuroVanL5-2.4L Diesel	Service typeBrake Drum Replacement	Estimate$496.99	Shop/Dealer Price$604.73 - $900.98
1996 Volkswagen EuroVanL5-2.5L	Service typeBrake Drum Replacement	Estimate$812.37	Shop/Dealer Price$971.58 - $1376.96
1995 Volkswagen EuroVanL5-2.5L	Service typeBrake Drum Replacement	Estimate$802.87	Shop/Dealer Price$961.02 - $1365.61
1993 Volkswagen EuroVanL5-2.5L	Service typeBrake Drum Replacement	Estimate$818.37	Shop/Dealer Price$976.10 - $1380.38
1995 Volkswagen EuroVanL5-2.4L Diesel	Service typeBrake Drum Replacement	Estimate$913.41	Shop/Dealer Price$1096.06 - $1572.48

Show example Volkswagen EuroVan Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Volkswagen mechanics

Real customer reviews from Volkswagen owners like you.

Excellent Rating

(34)

Rating Summary

28

2

0

1

3

28

2

0

1

3

SEE REVIEWS NEAR ME

ALAA

35 years of experience

56 reviews

ALAA

35 years of experience

by Julia DeMarines

EuroVan 1999 - Pre-purchase Car Inspection - El Macero, CA

He was early and thorough! He was able to help me decide if I should purchase a car with a pre-purchase check.

Michael

35 years of experience

131 reviews

Request Michael

Michael

35 years of experience

Request Michael

by Gay Cooper

EuroVan 2003 - Check Engine Light is on - Huntington Beach, CA

Michael is a true professional. He knows his stuff. He is the only mechanic I will use until he retires. (hopefully a long way off) I wouldn't hesitate to recommend his services to any friend or family member. Need an honest and knowledgeable mechanic, call Michael

Jeremy

15 years of experience

482 reviews

Jeremy

15 years of experience

by Katherine Semrod

EuroVan 1995 - Pre-purchase Car Inspection - Boynton Beach, FL

I had Jeremy do a pre-purchase inspection for me. He did a terrific job, and took the time to not only let me know potential issues with the vehicle but also gave me his opinion on the relative seriousness of each flaw he found. I really appreciated his experienced opinion!

Jay

30 years of experience

1009 reviews

Jay

30 years of experience

by William Taylor

EuroVan 2003 - Brake Light Switch - Sun City, CA

What a great experience! And guy!

Excellent Rating

(34)

Rating Summary

28

2

0

1

3

28

2

0

1

3

SEE REVIEWS NEAR ME

Recent articles & questions

Michigan Parking Laws: Understanding the Basics

Drivers Drivers in the state of Michigan need to know the laws related to parking. Namely, they need to know where they are not allowed to park. This will help to prevent them from getting parking tickets or getting their...

The Traveler’s Guide to Driving in South Africa

LMspencer / Shutterstock.com South Africa is a popular vacation destination (https://www.tripadvisor.com/Attractions-g293740-Activities-South_Africa.html) for those who are looking for the great outdoors as well as the comfort of modern cities. When you visit the country, you might want to...

How to Obtain an A3 ASE Study Guide and Practice Test

Automotive technician jobs pay more if you’re ASE certified. Get the study guide and practice test to be a A3 Manual Drive Train & Axles technician.

My car hesitates sometimes when I accelerate and wants to stall

Hesitation and stalling can be caused by a wide variety of issues, most of them relatively minor to repair. A few common causes are problems with the fuel, ignition, or engine management systems. If one of the components to these...

My car is slow to accelerate, and it stalls in drive and reverse

This may be related to a dirty or failing idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement). The idle air control valve monitors the air intake as it is mixed with fuel prior to being injected into the engine at low speeds and...

When trying to start the 2013 JX35 I pressed the brakes and push the start button and everything turn off even the inside light. W

It sounds like you're having an issue with the push button start system. It is possible that the issue could be caused by the push button itself. I would recommend having this particular system inspected by a qualified professional in...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com