Toyota Sienna Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Toyota Sienna Brake Drum Replacement is $283 with $188 for parts and $95 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2016 Toyota SiennaV6-3.5L	Service typeBrake Drum Replacement	Estimate$668.74	Shop/Dealer Price$805.94 - $1181.51
2001 Toyota SiennaV6-3.0L	Service typeBrake Drum Replacement	Estimate$606.90	Shop/Dealer Price$731.17 - $1058.89
2013 Toyota SiennaV6-3.5L	Service typeBrake Drum Replacement	Estimate$638.22	Shop/Dealer Price$775.81 - $1152.51
2007 Toyota SiennaV6-3.5L	Service typeBrake Drum Replacement	Estimate$615.24	Shop/Dealer Price$744.30 - $1090.99
2013 Toyota SiennaL4-2.7L	Service typeBrake Drum Replacement	Estimate$644.04	Shop/Dealer Price$783.11 - $1164.20
1999 Toyota SiennaV6-3.0L	Service typeBrake Drum Replacement	Estimate$606.90	Shop/Dealer Price$731.17 - $1058.88
2017 Toyota SiennaV6-3.5L	Service typeBrake Drum Replacement	Estimate$576.14	Shop/Dealer Price$695.99 - $1019.97
2012 Toyota SiennaV6-3.5L	Service typeBrake Drum Replacement	Estimate$646.22	Shop/Dealer Price$784.19 - $1161.18

Show example Toyota Sienna Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Toyota mechanics

Real customer reviews from Toyota owners like you.

Excellent Rating

(937)

Rating Summary

879

32

7

3

16

879

32

7

3

16

SEE REVIEWS NEAR ME

Jonathan

25 years of experience

42 reviews

Request Jonathan

Jonathan

25 years of experience

Request Jonathan

by Angelique Johnson

Sienna 2015 - Brake Rotor/Disc - Marietta, GA

He was very friendly and easy to understand where he was coming from with my car. I would recommend him to my friends and use his service again. My brakes are working very well also.

Johnathan

5 years of experience

41 reviews

Request Johnathan

Johnathan

5 years of experience

Request Johnathan

by Aleh Taranda

Sienna 2019 - Spark Plugs - Chesterfield, MO

Excellent job! Highly professional and knowledgeable.

Gregory

10 years of experience

25 reviews

Request Gregory

Gregory

10 years of experience

Request Gregory

by Karen Craft

Sienna 2008 - Oil Change - Fresno, CA

Gregory is flexible, courteous, and understands the concepts of what is needed to a vehicle.

Refugio

20 years of experience

49 reviews

Request Refugio

Refugio

20 years of experience

Request Refugio

by Carlos/carmen vazquez

Sienna 2017 - Heater Blower Motor - San Antonio, TX

Great service, friendly and knowledgeable.

Excellent Rating

(937)

Rating Summary

879

32

7

3

16

879

32

7

3

16

SEE REVIEWS NEAR ME

Recent articles & questions

Is it Safe to Drive With the ABS Light On?

The ABS warning light means the anti-lock braking system isn’t working properly, and may not work if you need to stop your car quickly.

The Guide to Legal Car Modifications in North Dakota

ARENA Creative / Shutterstock.com If you live in North Dakota or are planning to move to the state, it is important that you know whether your modified vehicle is within the laws in the state. The following...

How to Get an Oklahoma Driver's Permit

Oklahoma Oklahoma uses a graduated licensing program that requires all new drivers under 18 years old to begin driving under supervision, in order to practice safe driving before getting their full driver’s license. In order to receive the initial learner’s...

Difficulty shifting to higher gears

Hello there. Thanks for writing in about your 1972 Chevrolet El Camino. A few different faults could cause the vehicle to have shifting and acceleration problems. The most common would be the transmission linkage, low fluid level (https://www.yourmechanic.com/services/transmission-fluid-service), torque converter,...

My BMW 335i n54 coolant line hose o ring needed to replaced. I think coolant is leaking from there.

The best thing to do is get a coolant pressure test and hook it up to your radiator or reservoir and pressurize the system to 15 psi. If there is a leak, it will appear under a pressure. If you...

Just applied new brakes and I still hear metql grinding

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com