Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.
How A Diagnostic Works
Instantly book a certified mobile mechanic to come to you
Mechanic diagnoses the problem and quotes necessary repairs
Your vehicle is ready to go
Fair, upfront & transparent pricing for all services
Our certified mobile mechanics can come to you now.
On average, the cost for a Toyota MR2 Spyder Brake pressure is uneven Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.
| Car | Service | Estimate | Shop/Dealer Price |
|---|---|---|---|
| 2000 Toyota MR2 SpyderL4-1.8L | Service typeBrake pressure is uneven Inspection | Estimate$114.99 | Shop/Dealer Price$124.99 - $132.49 |
| 2005 Toyota MR2 SpyderL4-1.8L | Service typeBrake pressure is uneven Inspection | Estimate$94.99 | Shop/Dealer Price$105.01 - $112.52 |
| 2003 Toyota MR2 SpyderL4-1.8L | Service typeBrake pressure is uneven Inspection | Estimate$94.99 | Shop/Dealer Price$105.01 - $112.52 |
| 2004 Toyota MR2 SpyderL4-1.8L | Service typeBrake pressure is uneven Inspection | Estimate$94.99 | Shop/Dealer Price$104.99 - $112.48 |
| 2001 Toyota MR2 SpyderL4-1.8L | Service typeBrake pressure is uneven Inspection | Estimate$94.99 | Shop/Dealer Price$105.02 - $112.55 |
| 2002 Toyota MR2 SpyderL4-1.8L | Service typeBrake pressure is uneven Inspection | Estimate$94.99 | Shop/Dealer Price$105.01 - $112.52 |
We tend to take our brakes for granted until something goes wrong. During normal operations, you’ll press the brake pedal and the car will slow down. However, there may be times when pressing the brake pedal also results in a pull to one side or the other – this is an example of uneven brake pressure. There are many potential causes here.
In a normally operating brake system, the calipers will squeeze the rotors evenly on both sides of the car (or on all four corners in the case that you have four-wheel disc brakes). Pressurized fluid is sent to each caliper from the master cylinder in even amounts, and the force applied by each caliper is nearly identical.
This allows the car to slow down evenly, without any changes in direction. It also ensures even pad wear. However, in some instances, this does not happen. There are several possible reasons for uneven brake pressure, and not all of them have to do with the braking system.
Stuck Caliper: Perhaps the most obvious reason for brake pressure to be uneven is a stuck caliper. If the caliper is not free to slide back and forth on the slide pins, it will not engage the pad correctly. In fact, it might never completely disengage from the pad, creating a constant drag that can be noticed even when the brakes are not being used.
*Damaged Brake Line - Sometimes, brake line damage isn’t visible. If the inner liner of the line has been damaged, it can act like a restrictor, blocking the flow of fluid to the caliper and reducing braking force.
Stuck Piston: The piston in the caliper needs to move back and forth freely, but if part of the seal has become wedged between the body of the piston and the caliper, it will not move as needed. This can also create uneven brake pressure.
Bad Proportioning Valve: The proportioning valve is located under the hood and is responsible for adjusting the fluid pressure sent to the rear brakes. If the valve begins to fail, uneven brake pressure can result.
Pad Contamination: Another possible cause of brake pull (uneven pressure) is if fluid has contaminated the brake pad. This can be brake fluid, grease or even oil.
Using Two Different Types of Pads: If you have replaced the pads on one side the car but not the other (which is always a no-no), there’s a chance you’re using two different types of pads. Different manufacturers use varying pad materials with very different performance characteristics.
Uneven Tire Pressure: Oddly enough, uneven tire pressure can masquerade as uneven brake pressure. Check your tires to ensure that they are properly inflated – this can be an inexpensive, hassle-free fix in some situations.
A top-rated mobile mechanic will come to your home or office to inspect your car’s entire brake system, including the brake lines, pads, rotors, calipers, pistons and more in order to identify the underlying problem. The mechanic will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.
The mechanic will need to inspect the entire brake system in order to determine the underlying cause of uneven brake pressure. The mechanic may also need to test drive the car to verify pulling, and to test for other potential problems, including pedal pulsation.
Uneven brake pressure can be a sign of a serious problem. A stuck caliper can cause serious damage to the pads and rotors, and your stopping ability is compromised, as well. A damaged brake line will eventually fail completely. Pad contamination may be a sign of a brake fluid leak, an oil leak, or possibly a damaged CV boot if grease is the contaminant. A stuck piston can also be a very serious problem that can cost a lot of money if not caught in time. Have your brake system professionally inspected and maintained during normal maintenance. One of our mechanics can inspect and repair your brakes if you experience uneven brake pressure.
Fast and easy service at your home or office
Backed by 12-month, 12.000-mile guarantee
Real customer reviews from Toyota owners like you.
Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.
