Subaru XV Crosstrek Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Subaru XV Crosstrek Brake Drum Replacement is $364 with $212 for parts and $152 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2015 Subaru XV CrosstrekH4-2.0L	Service typeBrake Drum Replacement	Estimate$608.22	Shop/Dealer Price$730.29 - $1060.47
2015 Subaru XV CrosstrekH4-2.0L Hybrid	Service typeBrake Drum Replacement	Estimate$576.22	Shop/Dealer Price$698.31 - $1028.52
2013 Subaru XV CrosstrekH4-2.0L	Service typeBrake Drum Replacement	Estimate$576.22	Shop/Dealer Price$698.31 - $1028.51
2014 Subaru XV CrosstrekH4-2.0L Hybrid	Service typeBrake Drum Replacement	Estimate$576.22	Shop/Dealer Price$698.28 - $1028.45
2014 Subaru XV CrosstrekH4-2.0L	Service typeBrake Drum Replacement	Estimate$576.22	Shop/Dealer Price$698.34 - $1028.56

Show example Subaru XV Crosstrek Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Subaru mechanics

Real customer reviews from Subaru owners like you.

Excellent Rating

(62)

Rating Summary

61

1

0

0

0

61

1

0

0

0

SEE REVIEWS NEAR ME

Jose

17 years of experience

433 reviews

Jose

17 years of experience

by Kelly

Subaru XV Crosstrek H4-2.0L - Pre-purchase Car Inspection - Beaverton, Oregon

Jose did a fantastic job! Right on time. Answered any questions i had about my crosstrek. I would certainly recommend him.

Ricardo

14 years of experience

339 reviews

Request Ricardo

Ricardo

14 years of experience

Request Ricardo

by Viviana

Subaru XV Crosstrek H4-2.0L - CarGurus Pre-purchase Car Inspection - Long Beach, California

Very knowledgeable, answered all my questions and concerns. Gave me advice as I just bought the used car. Thank you for your service.

Marko

6 years of experience

24 reviews

Marko

6 years of experience

by Justin

Subaru XV Crosstrek H4-2.0L - Car Battery Replacement - San Diego, California

Excellent service! Prompt, fast, friendly, reasonably priced and completely professional. Replaced my battery and checked the engine/tire pressure while we waited on the charge. Highly recommend.

Genaro

13 years of experience

287 reviews

Genaro

13 years of experience

by Jonathan

Subaru XV Crosstrek H4-2.0L - Brake Pads Replacement (Front, Rear) - Katy, Texas

Great

Excellent Rating

(62)

Rating Summary

61

1

0

0

0

61

1

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2012 Suzuki Kizashi

This This affordable little sedan showed up on the market in 2010 as an effort to bolster Suzuki’s fading popularity in the United States car game. While it may not have saved the company’s American operations, it is still an...

How to Quickly Pay Off a Car Loan

Nobody wants to be in debt, and nobody likes paying interest on a loan (https://www.yourmechanic.com/article/how-to-determine-total-interest-paid-on-an-auto-loan) for longer than necessary. Unfortunately, paying off a car loan feels like it takes forever—month after month, the balance hardly seems to go down at...

B1922 OBD-II Trouble Code: Air Bag Safing Sensor Output Circuit Short To Battery

B1922 means a circuit in the air bag deployment system is causing it to not work properly. This is likely due to an electrical issue in the wiring.

lost control of one wheel. on the left. seems broken

It sounds like you had a tie rod ball joint break or another ball joint break (https://www.yourmechanic.com/services/ball-joint-front-replacement). You will have to have the vehicle towed to a shop for inspection, or to a safe area where a mobile mechanic can...

Clogged manifold intake runner bank 1 2005 Mercedes C230 Turbo

Hi - the clogged intake is a long-term "carbon clogging" from the turbocharger/EGR valve operation. The manifold must be removed, disassembled, cleaned and reinstalled. Tedious, and requires moderate DIYr skills. Unfortunately, this is not a service YourMechanic offers at this...

Occassional blinking wrench light and hard shift into second gear as well as occasional loss of forward motion with high rev.

Hi Robert. Thanks for contacting us tonight. The wrench light is a warning or service light, that indicates that the vehicle is due to for a routine service check. With 150,000 miles, this is rather common and often indicates a...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com