Saab 900 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Saab 900 Brake Drum Replacement is $202 with $107 for parts and $95 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1990 Saab 900L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$590.13	Shop/Dealer Price$709.54 - $1034.02
1982 Saab 900L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$707.19	Shop/Dealer Price$863.39 - $1298.19
1986 Saab 900L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$357.27	Shop/Dealer Price$425.99 - $598.34
1997 Saab 900L4-2.3L	Service typeBrake Drum Replacement	Estimate$519.23	Shop/Dealer Price$635.29 - $960.96
1991 Saab 900L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$560.13	Shop/Dealer Price$679.59 - $1004.10
1995 Saab 900L4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$463.35	Shop/Dealer Price$565.46 - $849.24
1992 Saab 900L4-2.1L	Service typeBrake Drum Replacement	Estimate$567.63	Shop/Dealer Price$686.86 - $1011.20
1993 Saab 900L4-2.1L	Service typeBrake Drum Replacement	Estimate$567.63	Shop/Dealer Price$687.42 - $1012.18

Show example Saab 900 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Saab mechanics

Real customer reviews from Saab owners like you.

Excellent Rating

(29)

Rating Summary

22

4

3

0

0

22

4

3

0

0

SEE REVIEWS NEAR ME

Frank

40 years of experience

57 reviews

Frank

40 years of experience

by claudia

Saab 900 L4-2.3L - Brake Hose Replacement (Passenger Side Rear) - Woodstock, Georgia

Frank is professional, responsive to the question, reliable and has great knowledge in practice and theory. My family and I felt that our car is in good hands in addition to that, he was very friendy.

Caster

28 years of experience

176 reviews

Caster

28 years of experience

by Nuriya

Saab 900 L4-2.0L Turbo - Oil Change - Petaluma, California

This was my first time using YourMechanic. Castor came highly recommended and for good reason, On time, quick, professional and friendly. I will definitely use this service again!

Jeremy

20 years of experience

597 reviews

Jeremy

20 years of experience

by Michael

Saab 900 L4-2.1L - Car shudders when turning Inspection - West Palm Beach, Florida

My car is a collector’s Saab of which only 300 were made, all in 1991. Jeremy was on time, prepared and super-competent. Diagnosed the issue, explained why he was confident in his diagnosis, checked lots of other things and reported on the general condition of this rare car. Friendly and professional. I highly recommend him.

Amor

43 years of experience

181 reviews

Amor

43 years of experience

by Joe

Saab 900 L4-2.0L Turbo - Idler Pulley - Hayward, California

Honest and knowledgable, was able to solve my issues and offer advice in the form of preventative maintenance. Will call again for Amor on any future repairs.

Excellent Rating

(29)

Rating Summary

22

4

3

0

0

22

4

3

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How Long Does an Exhaust Air Supply Tube Last?

Since Since 1966 car manufacturers have had the pressure on them to drastically reduce the amount of emissions that vehicles send out into the atmosphere. Technology has come a long way in that time, and has allowed for all kinds...

Rules of the Road For Wisconsin Drivers

Have Have you recently moved to Wisconsin and/or are you planning on doing some driving in this beautiful state? Whether you’ve lived in Wisconsin all your life or visiting, you might want to brush up on the rules of the...

Veteran and Military Driver Laws and Benefits in Arizona

The The state of Arizona offers a number of benefits and perks for those Americans who have either served in an Armed Forces branch in the past, or are current active military members. Vehicle registration benefits Residents on active duty...

Brake pad sensor on - 2014 Audi Q7

Hello. If the brake pad light came on, then that does typically mean that the vehicle needs brakes. It is possible that the sensor itself just shorted out, but I rarely see that on this vehicle. If the brakes are...

noise when car is running, sounds like wu, wu ,wu

Hello. Thanks for writing in. There a few things we need to clarify before we can begin delving into the issue. First, are we referring to you cooling system and engine fan, or the blower motor fan which is used...

My brake lights are not working, fuses are good

It is possible both bulbs are burned out. The filament in each bulb should be tested with an ohmmeter. The bulbs can also be powered off the car to see if both filaments work but be wary of short circuits...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com