Pontiac Sunbird Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Pontiac Sunbird Tie Rod End Replacement is $159 with $64 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1992 Pontiac SunbirdV6-3.1LService typeTie Rod End - Rear Right Outer ReplacementEstimate$308.85Shop/Dealer Price$365.44 - $510.46
1986 Pontiac SunbirdL4-1.8LService typeTie Rod End - Rear Right Inner ReplacementEstimate$372.95Shop/Dealer Price$446.96 - $637.45
1976 Pontiac SunbirdV6-3.8LService typeTie Rod End - Rear Right Outer ReplacementEstimate$258.85Shop/Dealer Price$308.46 - $432.49
1978 Pontiac SunbirdV6-3.8LService typeTie Rod End - Rear Right Outer ReplacementEstimate$258.85Shop/Dealer Price$308.43 - $432.45
1980 Pontiac SunbirdV6-3.8LService typeTie Rod End - Rear Right Outer ReplacementEstimate$258.85Shop/Dealer Price$308.48 - $432.52
1990 Pontiac SunbirdL4-2.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$286.85Shop/Dealer Price$343.46 - $488.49
1988 Pontiac SunbirdL4-2.0LService typeTie Rod End - Front Left Inner ReplacementEstimate$379.95Shop/Dealer Price$453.77 - $644.12
1992 Pontiac SunbirdV6-3.1LService typeTie Rod End - Front Left Outer ReplacementEstimate$289.15Shop/Dealer Price$345.22 - $488.05
Show example Pontiac Sunbird Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Pontiac mechanics

Real customer reviews from Pontiac owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Michael

40 years of experience
131 reviews
Michael
40 years of experience
Pontiac Sunbird L4-2.0L - Car is overheating - Columbus, Ohio
Michael was very professional, kind, courteous, attentive. He listened to what I had to say and helped to find the solution to the problem. Thank you, Mike, for everything you did to get me back on the road. 

John

6 years of experience
35 reviews
John
6 years of experience
Pontiac Sunbird V6-3.8L - Car does not move when I step on the gas pedal Inspection - Renton, Washington
John was super awesome and honest. He showed and explained why I needed certain things and was very helpful in making a well informed decision. Highly reccomend him.

Andrew

11 years of experience
862 reviews
Andrew
11 years of experience
Pontiac Sunbird L4-2.0L - Axle / CV Shaft Assembly Replacement (Driver Side Front) - Kansas City, Missouri
Very good experience with this service, Andrew was a true life saver. Will definitely be using this service again. I will definitely recommend this service to everyone that needs or could use it. Thank you

Joshua

27 years of experience
709 reviews
Joshua
27 years of experience
Pontiac Sunbird L4-2.0L - Ignition key does not turn - Oakland, California
Joshua was great. He arrived early which was a plus. He quickly resolved the problem and ordered the parts. I would recommend him to everyone. As a matter of fact while he was there attending my Mom's car, I had him to look at my car as well. He was wonderful and very professional.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Pontiac Sunbird services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Pontiac MECHANICS
800+
experts on our platform

Recent articles & questions

How to Get the Best Price on a Windshield Replacement
If If your windshield has a serious crack or is broken, you will need to have it replaced (https://www.yourmechanic.com/article/how-to-buy-a-good-quality-windshield) as soon as is possible. A seriously damaged or broken windshield can impair your visibility, and offers less protection in the...
P0359 OBD-II Trouble Code: Ignition Coil I Primary/Secondary Circuit Malfunction
P0359 P0359 code definition The P0359 code indicates that a fault has been detected in one of the vehicle’s ignition coils, generally the number 9 coil. This code can also be associated with P0351, P0352, P0353, P0354, P0355, P0356, P0357,...
P0779 OBD-II Trouble Code: Pressure Control Solenoid B Intermittent
P0779 means that the Pressure Control Solenoid B, is receiving intermittent voltage signals due to low or dirty fluid, faulty solenoid, or module.

Car chokes

Hesitation upon acceleration usually means the air/fuel mixture is lean or that there is an ignition misfire under load. Any of these conditions should set a diagnostic trouble code (DTC) and turn on the Check Engine Light. Retrieving the DTC...

People say it's a hole in my muffler but I don't know.

Hello, thanks for writing in about your 2001 Buick Regal. While some mufflers are able to be repaired, it is often times not a very permanent fix depending on the condition of the muffler and where the hole is. For...

I installed a new fuel sending unit the gas tank is full and it shows empty when u take all gas out it shows full what could it be

It sounds like you put in an incorrect sending unit or it is defective and needs a replacement. The fuel sending unit will vary resistance from low to high resistance controlling the gauge. If the signal from the sending unit...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com