Pontiac Sunbird Car Battery Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Car Battery Replacement Service

How much does a Car Battery Replacement cost?

On average, the cost for a Pontiac Sunbird Car Battery Replacement is $285 with $145 for parts and $140 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1991 Pontiac SunbirdV6-3.1L	Service typeCar Battery Replacement	Estimate$445.56	Shop/Dealer Price$521.80 - $742.42
1992 Pontiac SunbirdV6-3.1L	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$511.02 - $730.32
1993 Pontiac SunbirdL4-2.0L	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$511.05 - $730.36
1990 Pontiac SunbirdL4-2.0L	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$511.05 - $730.36
1993 Pontiac SunbirdV6-3.1L	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$512.52 - $732.94
1991 Pontiac SunbirdL4-2.0L	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$511.19 - $730.61
1990 Pontiac SunbirdL4-2.0L Turbo	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$511.06 - $730.39
1994 Pontiac SunbirdV6-3.1L	Service typeCar Battery Replacement	Estimate$436.55	Shop/Dealer Price$511.05 - $730.36

Show example Pontiac Sunbird Car Battery Replacement prices

What are car batteries and how do they work?

A car battery is an energy storage device that relies on a chemical reaction within the battery to produce electricity. The stored electrical energy is used to initially operate the starter motor, ignition system, and fuel system on your vehicle. Once your car engine is running, the alternator supplies the electricity needed for all vehicle systems and charges the battery to replace the electric energy used when starting a car.

Most electric vehicles have a traction battery which is in addition to the standard 12 volt battery that is used to start the car engine. Traction batteries also convert chemical energy to supply electrical energy but operate at higher voltages and often are monitored by the PCM (Powertrain Control Module).

Battery

When to replace a car battery?

Your car doesn’t start. A new battery has a specified capacity to provide power. This capacity is referred to as the cranking amps rating of the battery. As a battery ages, the actual amps that a battery can supply becomes lower than its original rating Once the cranking amps fall below a critical threshold, it will be difficult or impossible to start your car.
Battery or charging system warning light is illuminated. Should a battery or charging system warning light illuminate, a mechanic should perform a few basic tests to determine if a battery replacement is needed.
Electrical components don’t work. Once a battery has started to fail, and the voltage produced by the battery drops, then vehicle electrical components can malfunction, such as the security system. If you are experiencing electrical malfunctions, it’s a smart idea to have the battery tested.

How do mechanics replace the battery?

A temporary power source might be installed to avoid the possibility of losing radio presets or stored data in the PCM while the battery is out. When the battery is already completely dead, this step is unnecessary.
The vehicle’s negative cable is removed from the battery, followed by the positive cable. The battery tie down system is loosened and the old battery removed.
Cable ends and wiring are carefully inspected to ensure cleanliness and no corrosion. In some cases, corrosion can be extreme and the cable may need to be replaced or wiring repaired.
The new battery is installed and the tie down system is reinstalled. Anti-corrosion compound is applied to the battery terminals. The positive terminal is reconnected followed by the negative terminal.
Some vehicles, for example some models of BMW, VW, and Audi, may require PCM programming to input battery parameters. This step, performed using a specialized scan tool, is necessary to maximize battery life and prevent electrical system malfunctions.
The car is started and charging system output is measured and compared against the factory OEM specification to ensure that the new battery will properly recharge. Generally, charging output will be in the range of 13.8 to 14.8 volts but the exact specifications vary by make and model.

Is it safe to drive with a battery problem?

Yes, but if you have a weak battery you might be left stranded somewhere if the battery dies completely and you cannot start your car. A faulty battery may also needlessly overload the alternator and could adversely affect the operation of the vehicle’s electrical system, including the vehicle security system and the shift interlock.

When replacing the battery keep in mind:

The quality of the electrical connections to the battery posts is important. Connections must be clean, free of corrosion and properly tightened.
Batteries store a large amount of energy and if short-circuited a battery could explode and can create intense discharges that can damage your eyesight. Insulated tools should be used to attach cabling to battery terminals. Otherwise, the battery’s positive cable can be shorted to ground or the positive and negative posts can be directly shorted. Batteries can only be safely installed from a positive terminal to positive wiring and from a negative terminal to body ground. If the polarity is reversed damage will likely occur to the vehicle’s electrical system.
Generally, a car battery will have a service life of 4 to 7 years. If a load test on a battery reveals a significant reduction in the capacity of the battery to provide power, you should buy a new battery rather than wait for the old battery to fail completely.
Batteries should only be disconnected if the engine is off and the alternator is not running. Disconnecting a car battery while the alternator is running can cause a voltage spike that will damage sensitive electronic components in the vehicle, such as the PCM.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Pontiac mechanics

Real customer reviews from Pontiac owners like you.

Excellent Rating

(5)

Rating Summary

5

0

0

0

0

5

0

0

0

0

SEE REVIEWS NEAR ME

Paul

11 years of experience

38 reviews

Paul

11 years of experience

by Chantal

Pontiac Sunbird L4-2.0L - Ignition Lock Assembly - Austin, Texas

Joshua

28 years of experience

709 reviews

Joshua

28 years of experience

by Valerie

Pontiac Sunbird L4-2.0L - Ignition key does not turn - Oakland, California

Joshua was great. He arrived early which was a plus. He quickly resolved the problem and ordered the parts. I would recommend him to everyone. As a matter of fact while he was there attending my Mom's car, I had him to look at my car as well. He was wonderful and very professional.

John

7 years of experience

35 reviews

John

7 years of experience

by Andre

Pontiac Sunbird V6-3.8L - Car does not move when I step on the gas pedal Inspection - Renton, Washington

John was super awesome and honest. He showed and explained why I needed certain things and was very helpful in making a well informed decision. Highly reccomend him.

Michael

41 years of experience

131 reviews

Request Michael

Michael

41 years of experience

Request Michael

by Lucyan

Pontiac Sunbird L4-2.0L - Car is overheating - Columbus, Ohio

Michael was very professional, kind, courteous, attentive. He listened to what I had to say and helped to find the solution to the problem. Thank you, Mike, for everything you did to get me back on the road. 

Excellent Rating

(5)

Rating Summary

5

0

0

0

0

5

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

P2128 OBD-II Trouble Code: Throttle/Pedal Position Sensor/Switch "E" Circuit High Input

P2128 P2128 trouble code definition The pedal position sensor is used as an input to the engine control module (ECM) to determine the amount of torque requested by the operator. The ECM should receive an input that is within the...

How to Safely Drive in Stop-and-Go Traffic

It’s It’s a basic tenet of owning a car: nobody likes driving in traffic. Whether you’re stuck in traffic for five minutes as you look for the next exit, or spend two hours in congestion every day on your commute...

How to Buy a Good Quality Power Steering Fluid Reservoir

Your Your vehicle runs smoothly while you’re driving down the road due to the power steering fluid, making it important to assure that the fluid doesn’t leak. Check your power steering fluid reservoir regularly for cracks and chips and leakage...

Check engine light flashing

The traction control system monitors the steering stability of the vehicle and engages when loss of traction has been detected. This is done by the use of electronic sensors that communicate with the Power Train Control Module (PCM) regarding steering...

I hear a small noise every time I accelerate the gas

With the information you have provided, it sounds like you may be hearing the air as it is being drawn into the intake manifold. There are other possible causes, but this is the first thing that comes to mind when...

Losing power when I go up hills.

Hi there. When the car is climbing hills and the engine RPM goes up, but is slow to accelerate, it is due to the transmission downshifting to a lower gear ratio. However in some cases, the lack of acceleration can...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com