Mitsubishi Sigma Hazard / Turn Signal Flasher Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(1,979)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(1,979)

Hazard / Turn Signal Flasher Replacement Service

How much does a Hazard / Turn Signal Flasher Replacement cost?

On average, the cost for a Mitsubishi Sigma Hazard / Turn Signal Flasher Replacement is $188 with $93 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1990 Mitsubishi SigmaV6-3.0LService typeHazard / Turn Signal Flasher ReplacementEstimate$301.87Shop/Dealer Price$358.59 - $506.25
1989 Mitsubishi SigmaV6-3.0LService typeHazard / Turn Signal Flasher ReplacementEstimate$281.87Shop/Dealer Price$338.61 - $486.28
Show example Mitsubishi Sigma Hazard / Turn Signal Flasher Replacement prices

What is the Hazard / Turn Signal Flasher all about?

The hazard / turn signal flasher is a small, electrical device that causes the lights on your vehicle to flash in a rhythmic, steady fashion. It is usually located under the driver’s side of the dash, and is wired in-line with the turn signal lever and hazard switch buttons. When the turn signals or hazard lights are turned on, the circuit’s power is routed through the flasher, which only emits short bursts of power that cause the lights to flash. If the flasher is not working, your hazard or turn signal lights may stay on solid when turned on, not turn on at all, or flash at an undesirable rate.

Keep in mind:

  • Flasher units hardly ever develop problems. Although in older vehicles, the wiring can become compromised.
  • Don’t assume that the problem is with the flasher – it could be something as simple as a blown fuse.
  • Check your bulbs, and replace them if necessary.

How it's done:

  • The vehicle's hood is opened and supported manually
  • The new relays are installed onto a mounting bracket
  • The wiring is connected to the relays and into the vehicle harness
  • The hood manual support is removed
  • The install is verified and the hazard lights are tested for proper operation

Our recommendation:

If your turn signals aren’t working, you will fail a motor vehicle inspection or a roadside check. Examine your fuses to make sure none are discolored – this indicates a blown fuse that could be causing the problem. Check your light bulbs as well. If all are in good working order, then the problem could be the hazard / turn signal flasher, which is part of your car's electrical system. Have one of our expert mechanics inspect and replace the hazard turn signal flasher if required.

What common symptoms indicate you may need to replace the Hazard / Turn Signal Flasher?

  • No turn signals on either side
  • Turn signal on only one side
  • Turn signals light up but don’t flash
  • Turn signal flashes too slow
  • Turn signal flashes too fast
  • Hazard lights don’t work

How important is this service?

Malfunctioning turn signals and hazard lights are critical safety issues. If your turn signals aren’t working, you have no way of communicating your driving intentions to other drivers aside from hand signals. Have one of our expert mechanics check them immediately so that the problem can be diagnosed, and appropriate measures taken, such as replacing your hazard / turn signal flasher.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mitsubishi mechanics

Real customer reviews from Mitsubishi owners like you.

Excellent Rating

(1,979)

Rating Summary
1,851
73
15
13
27
1,851
73
15
13
27

Greg

22 years of experience
413 reviews
Greg
22 years of experience
Mitsubishi Outlander Sport L4-2.0L - Spare Tire Installation - Mesa, Arizona
Greg was very thorough and professional  . I am so grateful for this service.

Irven

11 years of experience
60 reviews
Irven
11 years of experience
Mitsubishi Eclipse V6-3.8L - Oxygen Sensor Replacement (Front/Upper/Upstream, Rear/Lower/Downstream) - Windsor Mill, Maryland
Right on time, friendly, knowledgeable, flexible, accommodating, professional. Did I leave any kudos out? The oxygen sensor was apparently installed cross threaded from the factory. He had to procure a tool to clear the threads in order to do the job. Marvelous job.

Albert

22 years of experience
81 reviews
Albert
22 years of experience
Mitsubishi Lancer L4-2.0L - Car is not starting - Snellville, Georgia
My experience was phenomenal. Albert was extremely knowledgeable and helped me even better understand my car. He found a solution to my problem in the allotted time allowed.

Rigoberto

11 years of experience
739 reviews
Rigoberto
11 years of experience
Mitsubishi Montero Sport V6-3.0L - Radiator - Chicago, Illinois
I would like him to become my go to mechanic

Excellent Rating

(1,979)

Rating Summary
1,851
73
15
13
27
1,851
73
15
13
27
Number of Mitsubishi services completed
21769+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mitsubishi MECHANICS
700+
experts on our platform

Recent articles & questions

Symptoms of Bad or Failing Wheel Bearings
Common signs include abnormal tire wear, grinding or roaring noise from the tire area, vibration in the steering wheel, and play in the wheels.
Wisconsin Speed Limits, Laws, and Fines
Following Following is an overview of the laws, limits, and fines as they relate to speeding traffic violations in the state of Wisconsin. Speed limits in Wisconsin 70 mph: interstates, expressways, and some four-lane highways 65 mph: some urban freeways...
How to Advertise Your Used Car With a Window Display
To To have more success when trying to sell your vehicle (https://www.yourmechanic.com/article/how-to-be-successful-when-selling-a-car-by-jason-unrau) it is necessary to advertise it even when you are on the go. In addition to cleaning your vehicle and making sure it looks its best, displaying for-sale...

stalls when put in gear

The idle control valve may be stuck or you have a vacuum leak. Try to disconnect the vacuum lines to the EGR valve to see if it still stalls. This may be due to problems in the vacuum system. Try...

My car won't start

Try to replace the battery and clean the battery terminals (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-battery-terminal-ends) first. It is also possible your Jeep has a defective totally integrated power module (TIPM). This module powers everything to do with starting and running the vehicle. The noise...

What is the average cost to replace the top on a 2003 BMW Z4 with an after market top?

Hi Amy. Thanks for writing in today. I am actually in the market for one myself for my 2009 128i and have been pricing them around. Most of the aftermarket BMW tops actually don't fit very well and typically require...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com