logo

Mercedes-Benz GLC300 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(11)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

(11)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz GLC300 Brake Drum Replacement is $539 with $378 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 Mercedes-Benz GLC300L4-2.0L TurboService typeBrake Drum ReplacementEstimate$955.18Shop/Dealer Price$1162.11 - $1744.64
2017 Mercedes-Benz GLC300L4-2.0L TurboService typeBrake Drum ReplacementEstimate$921.18Shop/Dealer Price$1128.14 - $1710.69
2016 Mercedes-Benz GLC300L4-2.0L TurboService typeBrake Drum ReplacementEstimate$916.78Shop/Dealer Price$1135.41 - $1724.24
2018 Mercedes-Benz GLC300L4-2.0L TurboService typeBrake Drum ReplacementEstimate$921.18Shop/Dealer Price$1128.10 - $1710.62
Show example Mercedes-Benz GLC300 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Number of Mercedes-Benz GLC300 services completed
121+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform
Yourmechanic was featured in

New York Times NBC CBS Forbes INC Tech Crunch

Learn more about us

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(11)
Rating Summary
11
0
0
0
0
11
0
0
0
0

Nicholas

11 years of experience
589 reviews
Request Nicholas
Nicholas
11 years of experience
Request Nicholas
by nick
Mercedes-Benz GLC300 L4-2.0L Turbo - Oil Change - Raleigh, North Carolina
I have used Nicholas 3 times and have been very pleased each time.

Mike

20 years of experience
43 reviews
Request Mike
Mike
20 years of experience
Request Mike
by Tammy
Mercedes-Benz GLC300 L4-2.0L Turbo - Oil Change - Stockbridge, Georgia
Service was Great. Mike xmas on time and very knowledgeable. Will request him again without a doubt.

Kenneth

20 years of experience
785 reviews
Request Kenneth
Kenneth
20 years of experience
Request Kenneth
by Lisa
Mercedes-Benz GLC300 L4-2.0L Turbo - Battery Voltage Converter - Carson, California
Absolutely one of if not, the best and most personable mechanics yet! Kenneth was tenacious about getting the needed part and his followup was supreme. Always on time and kept in contact on status of the part and his ETA. Meticulous when it came to putting enemy thing back as it should be as well. I will definitely call on him again! He is also a delight to chat with.

Saul

8 years of experience
17 reviews
Request Saul
Saul
8 years of experience
Request Saul
by LISA
Mercedes-Benz GLC300 L4-2.0L Turbo - Oil Change - Carson, California
He was in time and efficient. Came prepared and said he was familiar with luxury cars.

Excellent Rating

(11)
Rating Summary
11
0
0
0
0
11
0
0
0
0
Number of Mercedes-Benz GLC300 services completed
121+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform
Yourmechanic was featured in

New York Times NBC CBS Forbes INC Tech Crunch

Learn more about us

Recent articles & questions

Symptoms of a Bad or Failing Vacuum Pump
Common signs include poor fuel efficiency, difficulty pressing the brake pedal, oil leaking under the engine, and the AC not working.
Read more
Dodge Certified Pre-Owned (CPO) Car Program
Drivers Drivers who are shopping around for a used Dodge vehicle may want to consider cars under the Dodge certified pre-owned program. Many manufacturers have a certified pre-owned (CPO) program, and each one is set up differently. Read on to...
Read more
10 Best Stores to Buy Auto Parts in Colorado Springs, Colorado
Automotive technicians rely on auto parts stores to add and replace car parts. The best auto parts shop in Colorado Springs is O'Reilly.
Read more

Ignition not turning.

This is a common problem with the Ford Focus. Most likely, the ignition cylinder is bad and requires replacement. A certified technician, like one from YourMechanic, will be able to repair this for you (https://www.yourmechanic.com/services/ignition-key-is-stuck-and-does-not-turn-inspection).
Read more

Problems with gear shifting and transmission

It is possible that you could have a worn out transmission mount (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-engine-mount). The transmission mount is what connects the transmission to the body of the vehicle. The transmission will normally have some movement when it is shifting. The mount...
Read more

On my 2009 VW Passat the Check Engine Light diagnostic was performed yesterday the trouble code P2015. I would like an estimate on the repair

Read more
  1. Home
  2. Estimates
  3. Mercedes-Benz
  4. GLC300
  5. Brake Drum Replacement

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com

Read FAQ
GET A QUOTE