Mercedes-Benz CL63 AMG Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(13)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(13)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Mercedes-Benz CL63 AMG Tie Rod End Replacement is $177 with $82 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2009 Mercedes-Benz CL63 AMGV8-6.3LService typeTie Rod End - Rear Left Inner ReplacementEstimate$279.95Shop/Dealer Price$346.19 - $488.67
2008 Mercedes-Benz CL63 AMGV8-6.3LService typeTie Rod End - Front Left Inner ReplacementEstimate$259.95Shop/Dealer Price$326.24 - $468.74
2010 Mercedes-Benz CL63 AMGV8-6.3LService typeTie Rod End - Rear Left Outer ReplacementEstimate$315.75Shop/Dealer Price$395.98 - $580.34
2012 Mercedes-Benz CL63 AMGV8-5.5L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$315.75Shop/Dealer Price$395.93 - $580.24
2013 Mercedes-Benz CL63 AMGV8-5.5L TurboService typeTie Rod End - Rear Right Inner ReplacementEstimate$259.95Shop/Dealer Price$326.27 - $468.81
2014 Mercedes-Benz CL63 AMGV8-5.5L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$315.75Shop/Dealer Price$395.98 - $580.34
2014 Mercedes-Benz CL63 AMGV8-5.5L TurboService typeTie Rod End - Rear Right Outer ReplacementEstimate$320.75Shop/Dealer Price$400.64 - $584.74
2008 Mercedes-Benz CL63 AMGV8-6.3LService typeTie Rod End - Rear Right Outer ReplacementEstimate$320.75Shop/Dealer Price$401.58 - $586.37
Show example Mercedes-Benz CL63 AMG Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(13)

Rating Summary
13
0
0
0
0
13
0
0
0
0

Jermaine

24 years of experience
270 reviews
Jermaine
24 years of experience
Mercedes-Benz CL63 AMG V8-5.5L Turbo - Oil Change - Greenbelt, Maryland
Good Job .

David

13 years of experience
421 reviews
David
13 years of experience
Mercedes-Benz CL63 AMG V8-6.3L - Battery - Marietta, Georgia
Right on time. Great service.

Dana

25 years of experience
13 reviews
Dana
25 years of experience
Mercedes-Benz CL63 AMG V8-5.5L Turbo - Oil Change - Fairfax, Virginia
Job well done .

Yoel

9 years of experience
212 reviews
Yoel
9 years of experience
Mercedes-Benz E320 V6-3.2L - Tie Rod End Replacement (Front Right Inner, Front Right Outer) - Philadelphia, Pennsylvania
He did a great job, would recommend him to my freinds.

Excellent Rating

(13)

Rating Summary
13
0
0
0
0
13
0
0
0
0
Number of Mercedes-Benz Tie Rod End Replacement services completed
143+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

How Air Filters Affect Horsepower
Air Air filters work to clean the air entering your engine’s combustion chamber. A good supply of air and oxygen is very essential so that the engine can burn fuel efficiently and give you the horsepower you need to drive....
How to Find the Source of an Oil Leak
Oil Oil leaks are a very common problem that affects many car owners. Virtually all modern engines use some sort of oiling lubrication system, and a compromise in the sealing of this system will result in an oil leak. Whether...
P2626 OBD-II Trouble Code: O2 Sensor Pumping Current Trim Circuit/Open Bank 1 Sensor 1
P2626 Code Definition The P2626 code is a generic powertrain code related to computer circuit output issues. This code appears when the...

The best spark plug for Chevy Blazer

The best thing really--those things were designed for ACDelco plugs they came with. And if it didn’t come with the Radian spark plugs, buy the AC or Radian, because they last longest. Since spark plugs were designed for an engine,...

Replacing a power window motor - 2005 Chevrolet Equinox

If you have already removed the motor and regulator assembly but are unable to separate the two, I would recommend using a pry bar of some sort to try to separate the gears. If this does not work, it is...

Why would the ABS light be on if the ABS module does not see a problem or set a code?

Hi there: If the ABS warning light (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-the-abs-light-on) comes on while you are driving, it means the ABS is not working properly. Your normal brakes will work, but the anti-lock brakes will not. If the light remains on, you need...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com