Mercedes-Benz 500SEL Car pulls in one direction Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(5)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(5)

Car pulls in one direction Inspection Service

How much does a Car pulls in one direction Inspection cost?

On average, the cost for a Mercedes-Benz 500SEL Car pulls in one direction Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1984 Mercedes-Benz 500SELV8-5.0LService typeCar pulls in one direction InspectionEstimate$114.99Shop/Dealer Price$132.49 - $145.62
1992 Mercedes-Benz 500SELV8-5.0LService typeCar pulls in one direction InspectionEstimate$94.99Shop/Dealer Price$112.52 - $125.67
1993 Mercedes-Benz 500SELV8-5.0LService typeCar pulls in one direction InspectionEstimate$94.99Shop/Dealer Price$112.52 - $125.67
1985 Mercedes-Benz 500SELV8-5.0LService typeCar pulls in one direction InspectionEstimate$94.99Shop/Dealer Price$112.48 - $125.60
Show example Mercedes-Benz 500SEL Car pulls in one direction Inspection prices

Driving a car that pulls to one side is not only inconvenient, but it is also very dangerous. Maintaining constant pressure on the steering wheel to keep the car going straight is tiring and can pull your focus off the road. Plus, it can be very hard on your tires.

A pull to one side can be caused by a wide variety of issues -- everything from an underinflated tire to failed suspension parts.

Common reasons for this to happen:

Uneven Tire Pressure

Uneven tire pressure is a very common reason for a car to pull to one side. Lower pressure on one side changes the height of the tire, which causes the alignment to change. This is especially true if you have an underinflated rear tire. If the tire is underinflated, it will have increased rolling resistance which will make the pull to one side much more noticeable.

Over inflated tires are just as bad. This condition will also cause the alignment to change. An overinflated tire will cause the vehicle to push away from that tire, also creating abnormal tire wear.

You can see this in two ways:

  • An underinflated tire will show wear on the outer edges.
  • An overinflated tire will show wear down the center of the tire.

This is an easy fix: head to the local gas station and inflate all tires to their proper pressure. Tire pressure stipulations can usually be found on the driver’s side door jam. The optimal pressure is on a sticker. After you have inflated the tires back to their specifications, drive the vehicle to verify the pull is now gone.

Wheel Alignment

Another common cause of a car pulling to the side is a wheel that is out of alignment. Another symptom of misaligned wheels is uneven tread wear. Out-of-alignment wheels will quickly wear down and can lead to more serious issues if not addressed. You should have your vehicle aligned as soon as possible if this is the root cause of the pulling.

Alignment is not an adjustment of the wheels or tires, but of the suspension. A mechanic will adjust the suspension so that the angle of the tires is optimized and the tires make contact with the road according to the manufacturer specifications.

Brake Issues: Stuck Caliper, Collapsed Brake Hose, Unlubricated Slide Pins

Issues with the brake system can cause a vehicle to pull to one side. One of the most common brake issues is a stuck caliper. Brake calipers are powered by the hydraulic brake system and apply pressure to the brake pads to bring the car to a stop. If one of the calipers is stuck, the car will pull to that side.

Other brake issues that cause a car to pull include a collapsed brake hose, or slide pins that are in need of lubrication. Brake issues should be dealt with by a professional, as the braking system is a critical safety component of your car.

Bad Wheel Bearing

If you have a bad wheel bearing, there will probably be more serious symptoms present, but pulling to one side is also a warning sign.

Wheel bearings allow the friction-free rotation of the wheel hub assembly, providing smooth wheel rotation.

There are four wheel bearings on a vehicle, one at each wheel. When a wheel bearing wears out you will hear a grinding noise from the tire area, the steering wheel will sometimes shake, and the car will possibly pull to one side if it is starting to seize. This latter symptom often occurs long after you start hearing the grinding noise.

You should not drive your vehicle in this condition. Contact a mechanic immediately. Replacing a wheel bearing is a complicated repair and should be done by a professional.

Worn Suspension Components

At some point in your vehicle’s lifetime, most of the suspension will need replacing. Whether it is shocks or struts, ball joints, control arms or bushings, all the components wear out over time. As they become worn, they will often shift or lean to one side, especially during braking, which causes the car to pull to that side.

For example, a worn-out control arm bushing will shift when the brakes are applied, causing the vehicle to pull sharply to that side. Suspension parts tend to wear out slowly, so it is possible that you may not notice until they actually break.

The suspension is a key component of your car’s safety system and you should not drive it with broken or worn parts. An annual inspection of your suspension can help avoid surprises.

Worn Steering Linkage

A weak tie rod end will cause the steering wheel to shift to one side or the other while turning. If it gets extremely bad, the steering wheel could shake violently from side to side. Newer vehicles use a rack-and-pinion system that can sometimes be serviced. Older vehicles use a steering box and linkage system that is serviceable.

A broken or severely damaged steering linkage is extremely dangerous, as it could result in loss of control of the steering wheel. If you suspect any of these symptoms, have your car checked by a mechanic.

Torque Steer

Torque steer is when the car pulls to one side as the car initially accelerates. There can be several causes of this condition. Sometimes, loose steering components are the culprit. Other times, a broken motor mount is the cause. Too much slack in a tie rod, a failing lower control-arm bushing, or a ball joint with excess movement can all cause this problem.

You can test for this problem by putting your car in neutral and coasting it down the street. If the pull does not happen when coasting, your alignment is probably not the problem and torque steer could be the source of the issue.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the cause and source of the pulling issue, and will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.

How important is this service?

A car is not safe to operate under conditions where it is pulling to one side. Regardless of whether it is a brake issue, suspension issue, or a bad wheel bearing, these repairs require the expertise of a professional. Book a mechanic to perform a thorough inspection as soon as possible.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Theodore

16 years of experience
1628 reviews
Theodore
16 years of experience
Mercedes-Benz 500SEL V8-5.0L - Windows - Seattle, Washington
Theodore was excellent! He was on time and did what he said. He even worked through a hailstorm!!

Herman

13 years of experience
86 reviews
Herman
13 years of experience
Mercedes-Benz 500SEL V8-5.0L - Spark Plugs - Miami Beach, Florida
As good as it gets.

Herman

13 years of experience
86 reviews
Herman
13 years of experience
Mercedes-Benz 500SEL V8-5.0L - Ignition Cable (Spark plug wires) - Miami Beach, Florida
I have used his services twice and both times he has done a great job.

Horus

11 years of experience
122 reviews
Horus
11 years of experience
Mercedes-Benz 500SEL V8-5.0L - Power window is noisy - San Antonio, Texas
He knows a lot.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Mercedes-Benz 500SEL services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

The Guide to Right-of-Way Laws in Michigan
When When are you supposed to yield the right of way? Common sense would seem to dictate that you should do so any time it could prevent an accident. Of course, common sense does not always prevail, and that is...
How to Prepare for the Wyoming Driver’s Written Test
If If you want to drive in Wyoming, one of the first things you need to do is to make sure you pass the driver’s written test. You need to pass this test before you can get your learner’s permit,...
How to Diagnose Blown Car Speakers
Even Even the highest-quality audio systems wear out over time, especially if you like to listen to your music at a high volume. If your car’s speakers (https://www.yourmechanic.com/article/4-essential-things-to-know-about-your-car-s-stereo-and-speakers) seem muted or if they are not working at all, you need...

Pop/Thud noise when backing up

The noise you are hearing is most likely an outer constant velocity joint (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-axle-cv-shaft-assembly) on the right side or passenger side of the car. Have the axle joints checked to see if the outer joint boots are torn (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-cv-boot). If...

what causes transmission to not shift? 2001 Dodge Ram 1500

Hey there, thanks for writing in about your 2001 Dodge Ram 1500. This is a common issue on many automatic transmissions. There is a speed sensor (https://www.yourmechanic.com/services/speed-sensor-replacement) which is a magnetic coil that tells the vehicle's control module what the...

WHERE IS THE VAPOR CANISTER VENT VALVE ON 2012 CHEVROLET CAPTIVA V6? IS IT ON THE CANISTER? ALSO WHERE IS THE FUEL PRESSURE SENSOR

Hi there. The purge solenoid valve is typically located on the passenger side of the vehicle, under the hood and attached to the firewall. In order to locate yours and to review the correct removal and installation procedures, I would...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com