Mercedes-Benz 300SEL Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz 300SEL Brake Drum Replacement is $376 with $215 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1965 Mercedes-Benz 300SELL6-3.0L	Service typeBrake Drum Replacement	Estimate$837.35	Shop/Dealer Price$1016.33 - $1446.93
1991 Mercedes-Benz 300SELL6-3.0L	Service typeBrake Drum Replacement	Estimate$590.80	Shop/Dealer Price$727.94 - $1072.29
1990 Mercedes-Benz 300SELL6-3.0L	Service typeBrake Drum Replacement	Estimate$590.80	Shop/Dealer Price$727.94 - $1072.28
1971 Mercedes-Benz 300SELV8-3.5L	Service typeBrake Drum Replacement	Estimate$783.35	Shop/Dealer Price$962.30 - $1392.88
1963 Mercedes-Benz 300SELL6-3.0L	Service typeBrake Drum Replacement	Estimate$783.35	Shop/Dealer Price$962.48 - $1393.20
1989 Mercedes-Benz 300SELL6-3.0L	Service typeBrake Drum Replacement	Estimate$590.80	Shop/Dealer Price$727.94 - $1072.28
1968 Mercedes-Benz 300SELL6-2.8L	Service typeBrake Drum Replacement	Estimate$796.85	Shop/Dealer Price$975.26 - $1405.44
1970 Mercedes-Benz 300SELV8-3.5L	Service typeBrake Drum Replacement	Estimate$796.85	Shop/Dealer Price$977.03 - $1408.52

Show example Mercedes-Benz 300SEL Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5,558)

Rating Summary

5,170

189

54

28

117

5,170

189

54

28

117

SEE REVIEWS NEAR ME

Robert

17 years of experience

28 reviews

Robert

17 years of experience

by Lane

Mercedes-Benz 300SEL L6-3.0L - Drive Belt Tensioner - Newtown Square, Pennsylvania

Robert has a positive attitude and is very professional. He got my vintage (ancient?) Mercedes all patched up and running again. I would definitely recommend Robert without hesitation!

Eduardo

19 years of experience

550 reviews

Request Eduardo

Eduardo

19 years of experience

Request Eduardo

by Sonia

Mercedes-Benz C230 L4-1.8L Turbo - Check Engine Light is on - Houston, Texas

Eduardo was great. My appt was scheduled for 3pm, but he called and offered to come earlier, which helped me out a lot. He was very fast and gave me some really good information about what low cost steps I should take first, before having any costly unnecessary repairs. I would definitely book him again.

John

31 years of experience

53 reviews

John

31 years of experience

by Gard

Mercedes-Benz E320 V6-3.2L - Oil Change - Lexington, Massachusetts

Great job

Lamine

2 years of experience

8 reviews

Lamine

2 years of experience

by Edward

Mercedes-Benz SLK320 V6-3.2L - Spark Plugs - Orlando, Florida

Lamines was prompt, on-time, professional, efficient, meticulous, and informative.

Excellent Rating

(5,558)

Rating Summary

5,170

189

54

28

117

5,170

189

54

28

117

SEE REVIEWS NEAR ME

Recent articles & questions

Symptoms of a Bad or Failing AC Low Pressure Hose

Check for crimps, kinks, and traces of refrigerant on the hose. A failing AC low pressure hose may cause a lack of cold air from the AC system.

Cell Phones and Texting: Distracted Driving Laws in New York

New New York defines distracted driving as something that draws the driver’s attention away from the road. When this occurs, the driver is no longer able to operate the vehicle in a safe or defensive manner. Distracted driving can be...

Top Automotive News & Stories: August 27-September 2

This week's top auto news: Bosch water injection, new Cadillac cars, White House addresses traffic fatalities, electronic recall notices, and more.

Using a lot of oil, no leaks under car

Thinking your car may be burning oil is never a fun thing to experience. Our first step in resolving this concern is to investigate exactly where the missing oil is disappearing. This should start with asking your nearest Toyota dealer...

I need to replace the crankshaft sensor. Where is it located in the motor?

Hello. Carbon buildup and other issues can cause these sensors to fail prematurely. You will need to raise the vehicle to access the sensor best. Once below the right, or passenger, side of the vehicle, you will want to look...

I have a 2004 Chevy impala that doesn't move when it's in drive an i step on the gas peddle. Why?

This may be a number of different possibilities, however it sounds like it may be related to a transmission problem. This can happen for a few different reasons such as low transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service) or a faulty control solenoid. An...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com