Mazda B3000 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mazda B3000 Brake Drum Replacement is $414 with $195 for parts and $218 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2005 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$654.62	Shop/Dealer Price$775.16 - $1085.01
1994 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$608.70	Shop/Dealer Price$729.30 - $1039.24
1996 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$622.10	Shop/Dealer Price$746.04 - $1066.04
2002 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$608.62	Shop/Dealer Price$729.14 - $1038.99
2003 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$608.62	Shop/Dealer Price$729.23 - $1039.14
1997 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$660.09	Shop/Dealer Price$788.05 - $1111.05
2000 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$620.12	Shop/Dealer Price$740.38 - $1050.03
1995 Mazda B3000V6-3.0L	Service typeBrake Drum Replacement	Estimate$633.60	Shop/Dealer Price$758.09 - $1078.49

Show example Mazda B3000 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mazda mechanics

Real customer reviews from Mazda owners like you.

Excellent Rating

(33)

Rating Summary

30

3

0

0

0

30

3

0

0

0

SEE REVIEWS NEAR ME

Jeff

33 years of experience

441 reviews

Jeff

33 years of experience

by Randolph

Mazda B3000 V6-3.0L - Crankshaft Position Sensor - Sacramento, California

Very pleased, will use again

Richard

13 years of experience

601 reviews

Request Richard

Richard

13 years of experience

Request Richard

by Alexandra

Mazda B3000 V6-3.0L - Car is not starting - Las Vegas, Nevada

Richard arrived early and got right to work. He was very professional and helpful as well as diagnosing the problem fast.

Howard

30 years of experience

92 reviews

Howard

30 years of experience

by Peter

Mazda B3000 V6-3.0L - Heater Blower Motor Resistor - Decatur, Georgia

Howard did a great job and is a real nice guy. We had a blow motor replaced prior with another tech. Howard came and replaced the blower motor resistor. With these two fixes we really thought this would take care of the ventilation system issue, but I still don't have air blowing out of the center console, just on the top vents and those on the bottom. The repair is beyond the scope of the repair I asked for. That is not any one's fault, if anything is was mine Howard is five stars.

Jesse

16 years of experience

63 reviews

Jesse

16 years of experience

by Robert

Mazda B3000 V6-3.0L - Heater is not working - Daytona Beach, Florida

did a great job thanks!

Excellent Rating

(33)

Rating Summary

30

3

0

0

0

30

3

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Symptoms of a Bad or Failing Evaporator Temperature Sensor (Switch)

Common signs include lack of cold air coming from AC, temperature fluctuations, and the AC compressor not activating.

How to Get a Nevada Driver's Permit

In In the state of Nevada, all new drivers under the age of 18 must begin driving with a learner’s permit, in order to practice safe driving before getting their full driver’s license. In order to receive the initial learner’s...

Should I Buy Electric Automotive Power Tools?

Automotive technician jobs require electric power tools, which are user-friendly and easy to transport, but can be expensive.

Loose emergency brake lever

Yes, this is a safety issue. This means the parking brake may be broken, installed incorrectly, or out of alignment. This also means the brake may not be working to its full potential, or at all. The parking brake lever...

My car cranks but it won't turn on.

Hello, thank you for writing in. When dealing with a cranking, no-start situation you always need to think about the basics. The first three things you need to make sure you have are fuel, air, and spark. If you are...

Wrench light and engine light on

Generally, the check engine light (https://www.yourmechanic.com/services/check-engine-light-is-on-inspection) comes on when something fairly serious is going on with the vehicle. This can happen for many different reasons such as a faulty mass air flow sensor, a faulty O2 sensor, a bad catalytic...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com