Lexus LC500h Car starts and then dies Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(6)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(6)

Car starts and then dies Inspection Service

How much does a Car starts and then dies Inspection cost?

On average, the cost for a Lexus LC500h Car starts and then dies Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2022 Lexus LC500hV6-3.5L HybridService typeCar starts and then dies InspectionEstimate$114.99Shop/Dealer Price$124.99 - $132.49
2021 Lexus LC500hV6-3.5L HybridService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2020 Lexus LC500hV6-3.5L HybridService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.01 - $112.52
2019 Lexus LC500hV6-3.5L HybridService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$104.99 - $112.48
2018 Lexus LC500hV6-3.5L HybridService typeCar starts and then dies InspectionEstimate$94.99Shop/Dealer Price$105.02 - $112.55
Show example Lexus LC500h Car starts and then dies Inspection prices

Starting a vehicle only to have it quit immediately after can be confusing and annoying for many drivers especially if their vehicle has not experienced this type of issue before. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. It is important to monitor fuel levels as well as warning lights which can signal to the driver that a vehicle may quit unexpectedly.

How this system works:

To start a vehicle, the electrical system, composed of the battery and starter, turns the engine over. Once running, the engine requires a constant flow of gasoline and good spark to keep that fuel igniting. If gasoline is not readily available, or if there is not enough spark, the engine will quit. More modern vehicles with sophisticated computers may affect the way the vehicle runs. These computers help the car run efficiently but can also shut a car down if the fuel/air mixture is not correct. While an older vehicle may be less sophisticated and easier to diagnose, the computers on modern cars can provide more specific information when connected to a code scanner/reader.

Common reasons for this to happen:

  • Mass Airflow Sensor: The mass airflow sensor measures how much air is entering the engine and relays this information to the vehicle’s computer so that the right amount of fuel can be delivered from the fuel injectors. When a sensor begins to fail, the vehicle’s computer may generate an error code to indicate that something has gone wrong. An issue with the mass airflow sensor may manifest itself when a car starts and then stalls soon after starting.

  • Fuel Pump Relay: The fuel pump relay functions much like a fuse for an electric fuel pump. The fuel pump relay engages as the vehicle is started and starts the fuel pump. While the vehicle is running, the fuel pump relay turns off and the fuel pump is powered by the oil pressure sending unit. If the vehicle’s computer is unable to keep the fuel pump relay running throughout the starting process, the vehicle may start and quit immediately after starting.

  • Ignition Coil: Your vehicle’s ignition coil takes the low voltage of the battery and provides the thousands of volts needed to create a spark in the spark plugs. When an ignition coil begins to fail, it may struggle to provide consistent spark to the plugs, causing the engine to stall after starting.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the reason why the vehicle starts and then dies. The mechanic will then provide a detailed inspection report outlining why the vehicle quit and the cost of any repairs that need to be made.

How it's done:

A mechanic will begin diagnosing your vehicle’s issue by plugging a code reader/scanner into the vehicle’s computer. The mechanic should be able to get more information from your vehicle’s computer on what component has failed. Using this information, the mechanic can begin necessary repairs.

If your vehicle has a bad or failing mass airflow sensor, the mechanic will begin by finding the sensor in the engine bay and checking for any signs of failure. The mechanic should check the wire harness connected to the sensor to ensure that all of wires are properly connected. After removing the sensor, the mechanic should be able to discover the nature of the failure and replace the sensor.

If the mechanic suspects an issue with the fuel pump relay, he or she should check the vehicle’s computer for a problem. If the vehicle’s computer is having difficulty providing consistent power to the fuel pump relay, the computer may need to be reprogrammed or replaced. If the vehicle’s computer is functioning normally, the mechanic may need to replace the fuel pump relay.

If the mechanic suspects that the ignition coil may be faulty, he or she should first disconnect the battery before beginning work. The mechanic should then begin the process of disconnecting wires from the ignition coil and removing it from the engine bay. The mechanic will then install the new ignition coil and ensure that it is connected properly. The mechanic should then reconnect the battery and test the new coil.

With all repairs, the mechanic will ensure the newly installed parts work properly. The mechanic can then turn off and warning lights that may have come on while the vehicle was not running properly.

How important is this service?

If your vehicle is starting but dying soon after starting, you should have it checked out by a mechanic. Issues involving the fuel management and electrical systems will become worse if not dealt with. Diligence and paying attention to warning lights may help prevent further damage to critical engine component and may save money in repairs. A vehicle that quits after starting can be inconvenient and having a mobile mechanic inspect and repair you vehicle will ensure that you and your vehicle are back on the road soon.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Lexus mechanics

Real customer reviews from Lexus owners like you.

Excellent Rating

(6)

Rating Summary
6
0
0
0
0
6
0
0
0
0

Bobby

27 years of experience
88 reviews
Bobby
27 years of experience
Lexus IS250 V6-2.5L - Car starts and then dies - Charlotte, North Carolina
Bobby was very friendly and worked quickly. We were very happy.

Russell

27 years of experience
271 reviews
Russell
27 years of experience
Lexus IS250 V6-2.5L - Car starts and then dies - Union City, California
Excellent mechanic!

Christopher

17 years of experience
57 reviews
Christopher
17 years of experience
Lexus LS430 V8-4.3L - Car starts and then dies - Douglasville, Georgia
Again and again he’s the best ever!

Oreste

14 years of experience
149 reviews
Oreste
14 years of experience
Lexus IS300 L6-3.0L - Car starts and then dies - Miami, Florida
Orestes was very professional and knowledgeable. He was efficient and i felt very honest and fair. I would rebook for future service.

Excellent Rating

(6)

Rating Summary
6
0
0
0
0
6
0
0
0
0
Number of Lexus Car starts and then dies Inspection services completed
66+
services done by our mechanics
TOTAL NUMBER OF EXPERT Lexus MECHANICS
1100+
experts on our platform

Recent articles & questions

Cell Phones and Texting: Distracted Driving Laws in Michigan
Michigan Michigan defines distracted driving as any non-driving activity that takes the driver’s eyes away from the road while behind the wheel of a moving vehicle. These distractions are further broken down into three main areas: manual, cognitive, and visual....
P3412 OBD-II Trouble Code: Cylinder 2 Deactivation/Intake Valve Control Circuit High
P3412 means the cylinder valve control circulation is reading high due to electrical problems, bad sensor or solenoid, or low oil pressure.
How to Clean and Repack Wheel Bearings
A wheel bearing should be cleaned and repacked if there is abnormal tire wear, grinding coming from the car tires, or steering wheel vibration.

Problems putting in a spark plug in I had to thread the port for the plug now it won't stay in

You are supposed to thread the hole out and get all the material from cutting cleaned out of the hole and engine cylinder. After it is cleaned then you should clean the threads with brake cleaner that will dry quickly....

Hi I have a 2001 s10 that seems to have a wiring issue or something.

Hi there. Check the battery and make sure that it can hold a charge. Even though a battery can have 12.6 volts, it could have a bad cell causing a large draw. Place the battery on a load and see...

Where is tranmetion dipstick on Chev HHR

This would depend on if you have an automatic or a manual transmission in your HHR. If you have a manual transmission, there will be no dipstick as it is only servicable from underneath the vehicle. If you have an...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com