Infiniti G37 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Infiniti G37 Brake Drum Replacement is $336 with $212 for parts and $123 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2008 Infiniti G37V6-3.7L	Service typeBrake Drum Replacement	Estimate$573.73	Shop/Dealer Price$702.54 - $1037.79
2009 Infiniti G37V6-3.7L	Service typeBrake Drum Replacement	Estimate$547.73	Shop/Dealer Price$676.58 - $1011.86
2011 Infiniti G37V6-3.7L	Service typeBrake Drum Replacement	Estimate$547.73	Shop/Dealer Price$676.58 - $1011.85
2012 Infiniti G37V6-3.7L	Service typeBrake Drum Replacement	Estimate$547.73	Shop/Dealer Price$676.53 - $1011.76
2010 Infiniti G37V6-3.7L	Service typeBrake Drum Replacement	Estimate$547.73	Shop/Dealer Price$676.61 - $1011.91
2013 Infiniti G37V6-3.7L	Service typeBrake Drum Replacement	Estimate$547.73	Shop/Dealer Price$676.58 - $1011.85

Show example Infiniti G37 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Infiniti mechanics

Real customer reviews from Infiniti owners like you.

Excellent Rating

(416)

Rating Summary

403

3

1

2

7

403

3

1

2

7

SEE REVIEWS NEAR ME

Jason

15 years of experience

344 reviews

Jason

15 years of experience

by Sade

Infiniti G37 V6-3.7L - Battery - Queens Village, New York

Jason was personable and friendly. He started the job right away, showed me other items that needed attention in a non pushy informative manner that allowed me to assess their priority. I would happily recommend using this convenient service and selecting Jason to be your mechanic of choice.

David

13 years of experience

396 reviews

David

13 years of experience

by Garrad

Infiniti G37 V6-3.7L - Brake Pads Replacement (Front, Rear) - Marietta, Georgia

David did an excellent job, I most definitely recommend him. He pointed out that a service I requested (brake flush) wasn't actually required, so that made a very reasonably priced job even more reasonable. Thank you, David for helping keep my car in good condition!

MICHAEL

33 years of experience

184 reviews

Request MICHAEL

MICHAEL

33 years of experience

Request MICHAEL

by Nii

Infiniti G37 V6-3.7L - Car is not starting - Doylestown, Pennsylvania

Very very nice guy

Benji

22 years of experience

277 reviews

Benji

22 years of experience

by Scott

Infiniti G37 V6-3.7L - Camshaft Position Sensor - Chandler, Arizona

He is great to work with. Highly recommend.

Excellent Rating

(416)

Rating Summary

403

3

1

2

7

403

3

1

2

7

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2012 Audi A3 TDI

Consumers Consumers steered clear of hatchbacks for a while but Audi has brought a stylish, functional, high-end option into the arena and buyers have responded. The A3 TDI offers all the versatility and performance you expect from Audi in a...

How Long Does a Coolant Temperature Switch (Sensor) Last?

The coolant temperature switch (CTS) provides you with alerts when the engine temperature is rising or when it is overheating. It...

How to Anchor a Child Safety Seat

The purpose of child safety seats is to keep children safe when riding in a car. To ensure this, the seat must be installed and secured properly.

Knocking noise after putting car into park while moving

Hey, thanks for writing in to YourMechanic. The parking mechanism inside the transmission is designed to hold the vehicle from moving when you park it and is not designed to stop the vehicle at all. You most likely bent or...

Why does my 2008 Toyota Tundra make a loud metal rattling noise whens started

Hi there. This noise can be caused by a few things. Most of the time it is caused by a loose heat shield on the exhaust. When this occurs you will hear the noise as the shield rattles and some...

I want to know what wire is the high beam wire.

Hi there. The best thing to do is get a digital volt meter or test light and check the headlight high beam harness for power and that will tell you which wire is the power wire for the high beam...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com