GMC Savana 2500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC Savana 2500 Brake Drum Replacement is $370 with $208 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1999 GMC Savana 2500V8-5.7L	Service typeBrake Drum Replacement	Estimate$1196.33	Shop/Dealer Price$1405.43 - $1924.73
2009 GMC Savana 2500V8-6.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$667.20	Shop/Dealer Price$810.67 - $1202.73
1999 GMC Savana 2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$1100.33	Shop/Dealer Price$1309.51 - $1828.86
2001 GMC Savana 2500V6-4.3L	Service typeBrake Drum Replacement	Estimate$1100.33	Shop/Dealer Price$1309.40 - $1828.67
2004 GMC Savana 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$667.20	Shop/Dealer Price$810.69 - $1202.77
2003 GMC Savana 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$667.20	Shop/Dealer Price$810.66 - $1202.73
2012 GMC Savana 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$619.54	Shop/Dealer Price$748.73 - $1098.50
2016 GMC Savana 2500V8-6.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$594.30	Shop/Dealer Price$717.82 - $1049.13

Show example GMC Savana 2500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(30)

Rating Summary

29

0

1

0

0

29

0

1

0

0

SEE REVIEWS NEAR ME

Torrieanto

12 years of experience

632 reviews

Request Torrieanto

Torrieanto

12 years of experience

Request Torrieanto

by Ross

GMC Savana 2500 V8-6.0L - Oil/Fluid Leak - Clearwater, Florida

Totally Satisfied with Trey my mechanic. Quickly identified the leaks and gave me an estimate. Totally honest and knowledgeable. I feel confident with someone who knows his trade well. Trey is a mechanic you can trust.

David

27 years of experience

182 reviews

David

27 years of experience

by Randy

GMC Savana 2500 V8-4.8L - Bleed Brakes - San Francisco, California

Great company that provided a super mechanic named David. I would highly recommend Your Mechanic and especially David. David went above and beyond what was required to ensure my brakes were to my satisfaction. David diagnosed my problem as a broken brake line and instead of taking the easy way out and ordering the part (which would have taken 2 days to get) he "coupled" around the hole and had my van working. Even though the job took longer than expected, I was charged what was quoted (how often does that happen?). If you need mechanical work, don't waste your time with the rest just use the best: YOUR MECHANIC AND REQUEST DAVID YOU WON'T BE DISAPPOINTED.

Troy

40 years of experience

107 reviews

Troy

40 years of experience

by Greg

GMC Savana 2500 V8-5.0L - Distributor - Phoenix, Arizona

He was very professional And explained everything that was wrong with my vehicle

David

13 years of experience

424 reviews

David

13 years of experience

by Chip

GMC Savana 2500 V8-4.8L - Pre-purchase Car Inspection - Marietta, Georgia

David was on time and did a great job.

Excellent Rating

(30)

Rating Summary

29

0

1

0

0

29

0

1

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Make Your Own Car Cleaning Solutions

Keeping Keeping your car’s interior clean can sometimes feel like an uphill battle when you don’t have the right cleaners on hand. Cleaning products can be expensive and some cleaners use harsh chemicals that may pose certain health risks after...

Top 10 Car Hacks

Simplify your life with ten car hacks: charge your phone while you drive, use a tennis ball to park, and prevent dings with pool noodles.

What Does the Distance Warning Light Mean?

The distance warning light turns on when your car is in danger of hitting another car or obstructing object.

What warning messages can be displayed on the instrument panel?

The Driver Information Center, or DIC, is a small screen at the bottom of the tachometer that can display a variety of information to the driver. Some of the information can be selected by the driver and is used to...

Truck jerks and hesitates on acceleration

This may be a sign of a failing mass air flow sensor. The mass air flow sensor is a unit in the intake system that monitors air intake as it is mixed with fuel prior to being injected into the...

car pulls to right after being hit hard on left tire and slight dent on wheel well.

There was probably at least some damage to your tie rods. These are the connections between the steering rack and the wheel. If one is bent or fatigued, it could even be dangerous to drive the car. There are some...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com