Ford Thunderbird Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Ford Thunderbird Brake Drum Replacement is $263 with $168 for parts and $95 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1980 Ford ThunderbirdL6-3.3L	Service typeBrake Drum Replacement	Estimate$621.14	Shop/Dealer Price$731.43 - $1008.30
1973 Ford ThunderbirdV8-7.5L	Service typeBrake Drum Replacement	Estimate$866.96	Shop/Dealer Price$1050.75 - $1548.02
1992 Ford ThunderbirdV6-3.8L	Service typeBrake Drum Replacement	Estimate$833.19	Shop/Dealer Price$998.92 - $1426.25
1965 Ford ThunderbirdV8-6.4L	Service typeBrake Drum Replacement	Estimate$691.22	Shop/Dealer Price$831.01 - $1196.44
2002 Ford ThunderbirdV8-3.9L	Service typeBrake Drum Replacement	Estimate$512.63	Shop/Dealer Price$627.07 - $947.83
1996 Ford ThunderbirdV6-3.8L	Service typeBrake Drum Replacement	Estimate$785.69	Shop/Dealer Price$946.42 - $1369.99
1963 Ford ThunderbirdV8-6.4L	Service typeBrake Drum Replacement	Estimate$703.22	Shop/Dealer Price$842.74 - $1207.96
1965 Ford ThunderbirdV8-7.0L	Service typeBrake Drum Replacement	Estimate$775.72	Shop/Dealer Price$934.26 - $1354.52

Show example Ford Thunderbird Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(153)

Rating Summary

145

3

2

0

3

145

3

2

0

3

SEE REVIEWS NEAR ME

Joe

43 years of experience

823 reviews

Joe

43 years of experience

by Lawrence

Ford Thunderbird V8-4.6L - Ball Joint Front Replacement (Lower Right) - Saint Petersburg, Florida

Joe arrived on time and completed the job to my absolute satisfaction.

Joe

43 years of experience

823 reviews

Joe

43 years of experience

by Lawrence

Ford Thunderbird V8-4.6L - Ball Joint Front Replacement (Lower Left) - Saint Petersburg, Florida

Joe arrived on time completed all work successfully and professionally,and in a timely manner. I absolutely recommend Joe,he is very knowledgeable,so no worries he can do the job !!!

Stan

12 years of experience

14 reviews

Stan

12 years of experience

by Diane

Ford Thunderbird V8-3.9L - Car Battery Replacement - North Charleston, South Carolina

Stan was very professional, knowledgeable, and personable.

Nelson

26 years of experience

163 reviews

Nelson

26 years of experience

by Ms

Ford Thunderbird V8-4.6L - Car is not starting - Sacramento, California

Nelson was quick and efficient and figured out the problem quickly.

Excellent Rating

(153)

Rating Summary

145

3

2

0

3

145

3

2

0

3

SEE REVIEWS NEAR ME

Recent articles & questions

P0040 OBD-II Trouble Code: O2 Sensor Signals Swapped Sensor 1

P0040 P0040 code definition P0040 indicates that there is an issue with the oxygen sensor sensor 1 circuit. This code can be in conjunction with P0041 What the P0040 code means P0040 is a specific code indicating a problem with...

P0699 OBD-II Trouble Code:Sensor Reference Voltage “C” Circuit High

P0699 means a fault in the sensor reference C circuit, which also affects the alternative fuel, body, anti-lock brake, and other control modules.

How Cars Get Safety Tested (How IIHS Safety Works)

The Insurance Institute for Highway Safety (IIHS) provides car safety ratings on front crash, side crash, head restraints, and roof strength.

Why doesn't my turn signals work unless I press the emergency lights first and why does my hot & cold meter not moving

Hello there, you have a few different faults with your 2001 Chevrolet Monte Carlo. If the turn signals do not work without the hazard lights than the most common failure would be a turn signal stalk failure, wiring harness fault,...

Idle fluctuates and then stalls.

Hi There, It sounds like you may have a dirty or failing idle air control valve causing your engine idle to fluctuate and eventually stall. The idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) is a small valve on the engine's intake system...

Reset AdBlue light on a mercedes GL

Hi There, Normally, this message will go away on its own after driving the vehicle for 5-10 miles. When you fill the tank, be sure to fill it to the top and it should relearn the new level of fluid...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com