Dodge Grand Caravan Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(7)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(7)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a Dodge Grand Caravan Power Steering Pressure Hose Replacement is $223 with $83 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2010 Dodge Grand CaravanV6-3.8LService typePower Steering Pressure Hose ReplacementEstimate$484.46Shop/Dealer Price$570.43 - $820.22
2006 Dodge Grand CaravanV6-3.8LService typePower Steering Pressure Hose ReplacementEstimate$330.29Shop/Dealer Price$378.20 - $517.80
1995 Dodge Grand CaravanV6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$724.19Shop/Dealer Price$870.60 - $1305.64
1996 Dodge Grand CaravanV6-3.8LService typePower Steering Pressure Hose ReplacementEstimate$311.13Shop/Dealer Price$354.27 - $479.52
2007 Dodge Grand CaravanV6-3.8LService typePower Steering Pressure Hose ReplacementEstimate$330.29Shop/Dealer Price$379.70 - $520.42
2008 Dodge Grand CaravanV6-4.0LService typePower Steering Pressure Hose ReplacementEstimate$416.09Shop/Dealer Price$485.61 - $689.69
2005 Dodge Grand CaravanV6-3.3LService typePower Steering Pressure Hose ReplacementEstimate$330.29Shop/Dealer Price$378.24 - $517.87
1995 Dodge Grand CaravanV6-3.3LService typePower Steering Pressure Hose ReplacementEstimate$448.09Shop/Dealer Price$525.47 - $753.44
Show example Dodge Grand Caravan Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0
Number of Dodge Grand Caravan Power Steering Pressure Hose Replacement services completed
77+
services done by our mechanics
TOTAL NUMBER OF EXPERT Dodge MECHANICS
1400+
experts on our platform

Recent articles & questions

P0785 OBD-II Trouble Code: Shift/Timing Solenoid Malfunction/ 3-2 Shift Solenoid Circuit Electrical
P0785 means there was an abnormality detected in the shift/time solenoid often due too a faulty shift solenoid or failures in the transmission.
How to Replace an Exhaust Gas Recirculation (EGR) Control Solenoid
Exhaust gas recirculation (EGR) systems are controlled by the EGR control solenoid, which is controlled by the powertrain control module (PCM).
How to Renew Your Car Registration in Kentucky
Getting Getting to and from work on a daily basis in Kentucky can only be done by having a car that is legal to drive. There are a variety of things that a person will need to do in order...

Transmission fluid leaking out overnight

Transmission leaks can come from either the pan gasket, output shaft seal, input shaft seal, or the cooler lines that take pressurized fluid through a heat exchanger in the radiator, or through its own dedicated cooler which looks like a...

How can I tell if my starter is going bad? 2008 BMW 528i

Hello - the slight delay in starter (https://www.yourmechanic.com/article/how-long-does-a-starter-last) function (and engine shut-down as well on some) for the "auto start sequence" seems to include a slight delay for most model vehicles with this feature. Whether this is an intentional delay...

03 Honda Accord EX which starts, shakes, then dies, yet when restarted cranks up just fine and runs. Ideas??

My first guess is that you may have a leaking fuel injector. When an injector is leaking from the tip, there is no visible sign. When you shut off the engine, the tip of the injector will drip into the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com