Chrysler Daytona Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chrysler Daytona Brake Drum Replacement is $313 with $199 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1991 Chrysler DaytonaV6-3.0L	Service typeBrake Drum Replacement	Estimate$811.68	Shop/Dealer Price$947.12 - $1272.41
1992 Chrysler DaytonaV6-3.0L	Service typeBrake Drum Replacement	Estimate$739.68	Shop/Dealer Price$875.18 - $1200.52
1984 Chrysler DaytonaL4-2.2L Turbo	Service typeBrake Drum Replacement	Estimate$634.66	Shop/Dealer Price$758.99 - $1075.66
1990 Chrysler DaytonaL4-2.5L	Service typeBrake Drum Replacement	Estimate$739.68	Shop/Dealer Price$875.10 - $1200.37
1989 Chrysler DaytonaL4-2.5L	Service typeBrake Drum Replacement	Estimate$516.75	Shop/Dealer Price$629.48 - $940.58
1993 Chrysler DaytonaL4-2.5L	Service typeBrake Drum Replacement	Estimate$587.70	Shop/Dealer Price$707.17 - $1020.48
1991 Chrysler DaytonaL4-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$757.68	Shop/Dealer Price$892.69 - $1217.66
1993 Chrysler DaytonaV6-3.0L	Service typeBrake Drum Replacement	Estimate$597.70	Shop/Dealer Price$717.64 - $1031.31

Show example Chrysler Daytona Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(9)

Rating Summary

9

0

0

0

0

9

0

0

0

0

SEE REVIEWS NEAR ME

Guillermo

15 years of experience

16 reviews

Request Guillermo

Guillermo

15 years of experience

Request Guillermo

by Frances

Chrysler Pacifica V6-3.5L - Brake Drum - Denver, Colorado

Guillermos was very courteous and informative. He keep me updated on his arrival time. Did a great job in a timely manner. Would definitely recommend him

Tyler

27 years of experience

178 reviews

Tyler

27 years of experience

by Swathi

Chrysler Sebring L4-2.4L - Brake Drum - Houston, Texas

Friendly and professional

Jerry

8 years of experience

136 reviews

Jerry

8 years of experience

by DAVID

Chrysler PT Cruiser L4-2.4L - Brake Drum - Lawrenceville, Georgia

Jerry, is a skilled mechanic.

Kenneth

16 years of experience

113 reviews

Request Kenneth

Kenneth

16 years of experience

Request Kenneth

by Maggie

Chrysler PT Cruiser L4-2.4L - Brake Drum - Oakland, California

Kenneth arrived early to complete the rear brake service on my car. He is very personable, service minded and a valuabe asset to the Your Mechanic organization. He is my go-to guy for any car servicing needs in the future. Thank you so much!

Excellent Rating

(9)

Rating Summary

9

0

0

0

0

9

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Child Seat Safety Laws in Louisiana

In In the State of Louisiana, everyone who transports children in motor vehicles is subject to certain laws, which are based in common sense, and designed to protect children. Failure to obey the laws can result in penalties, but that...

P2337 OBD-II Trouble Code: Cylinder #2 Above Knock Threshold

P2337 P2337 code definition The P2337 trouble code signals a problem with the #2 cylinder being above the knock threshold. What the P2337 code means The P2337 code is a standard OBD-II trouble code that deals with the #2 cylinder...

How to Replace a Trunk Lock Actuator

A car trunk is secured by a trunk lock that uses an electronic or mechanical lock actuator. A bad actuator prevents the lock from working properly.

Engine power loss

Hello. Although the symptoms may feel like a misfire, it's worth checking out the transmission too, since the transmission on this vehicle has multiple technical repair bulletins pertaining to the transmission lower gears causing jerking, noise like whining can be...

There is a repititive squeak during acceleration usually between 1,000 and 2,000 rpms. CVT

Hello. Typically squealing noises (https://www.yourmechanic.com/services/loud-squealing-or-rattling-is-coming-from-engine-inspection) related to engine speed are attributed to the drive belts. It may be a pulley, or the belt itself slipping. This can happen for many reasons. It does not happen in Park because the engine...

making a grinding noise when I drive the sound seems to be coming from the rear. Noticibe all the time but more when I am turning

You will need to have the rear brakes checked first to see if brakes are worn down to metal. If brakes are okay then you will have a problem in the rear axle bearings and a mechanic can isolate the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com