Chevrolet Tahoe Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Tahoe Brake Drum Replacement is $342 with $180 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2005 Chevrolet TahoeV8-5.3L	Service typeBrake Drum Replacement	Estimate$681.72	Shop/Dealer Price$820.29 - $1197.72
2000 Chevrolet TahoeV8-4.8L	Service typeBrake Drum Replacement	Estimate$740.44	Shop/Dealer Price$870.64 - $1171.05
2004 Chevrolet TahoeV8-5.3L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2000 Chevrolet TahoeV8-5.3L	Service typeBrake Drum Replacement	Estimate$740.44	Shop/Dealer Price$870.54 - $1170.89
2018 Chevrolet TahoeV8-6.2L	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.74 - $1023.65
2008 Chevrolet TahoeV8-6.0L Hybrid	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2004 Chevrolet TahoeV8-4.8L	Service typeBrake Drum Replacement	Estimate$656.22	Shop/Dealer Price$794.58 - $1171.86
1995 Chevrolet TahoeV8-5.7L	Service typeBrake Drum Replacement	Estimate$840.43	Shop/Dealer Price$979.77 - $1287.05

Show example Chevrolet Tahoe Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(1,036)

Rating Summary

989

25

4

4

14

989

25

4

4

14

SEE REVIEWS NEAR ME

Andrew

11 years of experience

841 reviews

Andrew

11 years of experience

by Stacy

Chevrolet Tahoe V8-5.3L - Water Pump - Kansas City, Kansas

2nd time using this service excellent experience

Dan

39 years of experience

975 reviews

Dan

39 years of experience

by Jamie

Chevrolet Tahoe V8-5.3L - Spark Plugs - Norcross, Georgia

Friendly and efficient, it’s clear Dan knows his way around an engine. He was early and finished quickly. Overall great experience as far as car repairs go.

Kelly

34 years of experience

173 reviews

Kelly

34 years of experience

by George

Chevrolet Tahoe V8-5.3L - Car does not shift from park to drive - Charlotte, North Carolina

Great

Michael

16 years of experience

606 reviews

Request Michael

Michael

16 years of experience

Request Michael

by Tony

Chevrolet Tahoe V8-5.3L - Check Engine Light is on - Atlanta, Georgia

Michael was on time, and very knowledgeable at what he does. Takes his time to explain the problem with your vehicle.

Excellent Rating

(1,036)

Rating Summary

989

25

4

4

14

989

25

4

4

14

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2012 Ford Flex

The The 2012 Ford Flex takes on a completely different look when it comes to a CUV. The Flex can tow up to 4,500 pounds and seat seven passengers comfortably. It also has lots of standard features that its competitors...

Symptoms of a Bad or Failing Canister Purge Solenoid

Common signs of a problem with a car EVAP canister purge solenoid include rough idle, difficulty starting, and the Check Engine Light turning on.

P0317 OBD-II Trouble Code: Rough Road Hardware Not Present

P0317 P0317 code definition The P0317 code means that the PCM has indicated that rough road hardware is not present. What the P0317 code means When the P0317 code is present, the powertrain control module has found a variation in...

Car idles high at startup

The idle air control valve on your car may be defective, causing the high idle. A couple of checks would need to be done to determine if this is the case. Your engine needs to be checked for any vacuum...

lights not working - 2003 Mazda Protege5

Hello. It sounds like there is some sort of short in the system. If you have had any work done on the vehicle, I would check for damaged wires in that area. If using a volt meter, check the available...

Truck stuck in 2nd gear (I believe), won't turn over, can't afford to bring it anywhere. Need help fast

Hi there. What seems to have happen is the shifter inside the transmission has came off the main valve and is making the valve only go into 1st and 2nd. To fix this, drop the transmission oil pan and oil....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com