Chevrolet Silverado 3500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Silverado 3500 Brake Drum Replacement is $414 with $253 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2003 Chevrolet Silverado 3500V8-6.0L	Service typeBrake Drum Replacement	Estimate$723.64	Shop/Dealer Price$872.69 - $1281.56
2001 Chevrolet Silverado 3500V8-6.0L	Service typeBrake Drum Replacement	Estimate$689.64	Shop/Dealer Price$838.72 - $1247.61
2002 Chevrolet Silverado 3500V8-6.0L	Service typeBrake Drum Replacement	Estimate$689.64	Shop/Dealer Price$838.71 - $1247.61
2003 Chevrolet Silverado 3500V8-6.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$689.64	Shop/Dealer Price$838.67 - $1247.54
2001 Chevrolet Silverado 3500V8-6.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$689.64	Shop/Dealer Price$838.74 - $1247.65
2003 Chevrolet Silverado 3500V8-8.1L	Service typeBrake Drum Replacement	Estimate$689.64	Shop/Dealer Price$838.71 - $1247.61
2006 Chevrolet Silverado 3500V8-8.1L	Service typeBrake Drum Replacement	Estimate$675.70	Shop/Dealer Price$818.93 - $1210.82
2006 Chevrolet Silverado 3500V8-6.0L	Service typeBrake Drum Replacement	Estimate$675.70	Shop/Dealer Price$819.57 - $1211.93

Show example Chevrolet Silverado 3500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(8)

Rating Summary

8

0

0

0

0

8

0

0

0

0

SEE REVIEWS NEAR ME

Tabitha

17 years of experience

332 reviews

Request Tabitha

Tabitha

17 years of experience

Request Tabitha

by William

Chevrolet Silverado 3500 V8-6.6L Turbo Diesel - Electrical components are not working - Del Mar, California

Tabatha was knowledgable and insightful in analyzing my problem. I would certainly ask for her when I have problems.

Chris

22 years of experience

2252 reviews

Chris

22 years of experience

by ken

Chevrolet Silverado 3500 V8-8.1L - Battery - Menifee, California

Arrived on time - extremely knowledgeable - highly motivated - highly recommend!!!!

Jeremy

20 years of experience

630 reviews

Jeremy

20 years of experience

by Deborah

Chevrolet Silverado 3500 V8-6.6L Turbo Diesel - Car is not starting - West Palm Beach, Florida

Jeremy came to the appointment in a timely manner. He was professional and easy to communicate with. He diagnosed the problem quickly, explained it to me in layman's terms and fixed it in no time.

Jay

37 years of experience

965 reviews

Jay

37 years of experience

by Chuck

Chevrolet Silverado 3500 V8-6.6L Turbo Diesel - Oil Change - Nuevo, California

Jay is very good and has been doing this for a long time. But what makes him so different is he has integrity. Twice now, he has passed on doing a job because it did not need to be done. Most mechanics and for sure dealerships would have turned a blind eye and did the job. Example-With my last job, my brakes start making what I thought was a worn-out pad. My truck had 127K on it, and the brakes pads have never been done. Who knew you could get 200K out of a set of brake pads. Anyway, I had already purchased the pads and had them waiting for Jay. After inspecting all four brakes, he called me. He explained he could do the job, but the pads are only about 60% worn, and I should be able to make 200K. Of course, I passed on the brake job and just paid Jay for the inspection time. I wish other mechanics were this honest. Honesty will keep the customer coming back, and that is why Jay is my goto mechanic.

Excellent Rating

(8)

Rating Summary

8

0

0

0

0

8

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

P0244 OBD-II Trouble Code: Turbocharger Wastegate Solenoid A Circuit Range/Performance

P0244 code definition Turbocharger Wastegate Solenoid A Circuit Range/Performance What the P0244 code means P0244 is an OBD-II generic code indicating that...

How to Replace an Evaporative Emission Control Canister

Emissions are regulated by the EVAP emission control canister which fails when the fuel tank gauge does not work or you fail an emissions test.

How to Replace a Trunk Lock Cylinder

A car trunk is secured by a trunk lock, which works via a trunk lock cylinder. Replacing a bad cylinder is imperative to your vehicle’s security.

Car sputters, shakes, and check engine light on

A good first step that you can perform is to check the engine for air leaks. Any rubber boot, bellows or vacuum hose that is allowing air to leak in can affect the way the car runs. Whether or not...

No power any were, fully charged battery.

Hi There, You may want to double check the ground connection to the chassis of the truck. As you may know, the ground wire connects the vehicle battery to the metal chassis, completing a circuit. Without the ground wire, the...

My 2015 Tahoe rides really, really rough. Any reason you think it rides rough?

Hello, There are a number of things that may cause the vehicle to ride rough such as worn out suspension components or suspension components that are improperly adjusted, worn control arm bushings or worn out ball joints. A ball joint...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com