Chevrolet Lumina APV Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(10)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(10)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Lumina APV Brake Drum Replacement is $386 with $177 for parts and $209 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1990 Chevrolet Lumina APVV6-3.1LService typeBrake Drum ReplacementEstimate$607.20Shop/Dealer Price$717.76 - $999.92
1995 Chevrolet Lumina APVV6-3.1LService typeBrake Drum ReplacementEstimate$605.44Shop/Dealer Price$722.47 - $1017.23
1992 Chevrolet Lumina APVV6-3.1LService typeBrake Drum ReplacementEstimate$576.94Shop/Dealer Price$690.97 - $983.47
1991 Chevrolet Lumina APVV6-3.1LService typeBrake Drum ReplacementEstimate$563.20Shop/Dealer Price$673.74 - $955.90
1995 Chevrolet Lumina APVV6-3.8LService typeBrake Drum ReplacementEstimate$605.44Shop/Dealer Price$722.51 - $1017.29
1996 Chevrolet Lumina APVV6-3.4LService typeBrake Drum ReplacementEstimate$605.44Shop/Dealer Price$722.47 - $1017.22
1993 Chevrolet Lumina APVV6-3.8LService typeBrake Drum ReplacementEstimate$617.94Shop/Dealer Price$734.63 - $1029.13
1994 Chevrolet Lumina APVV6-3.1LService typeBrake Drum ReplacementEstimate$617.94Shop/Dealer Price$735.56 - $1030.76
Show example Chevrolet Lumina APV Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(10)

Rating Summary
10
0
0
0
0
10
0
0
0
0

Andrew

11 years of experience
860 reviews
Andrew
11 years of experience
Chevrolet Lumina APV V6-3.1L - Starter - Shawnee Mission, Kansas
Called when he running behind. Very professional and stuck with a difficult problem until finished. Would I use him again? A definite yes!

Richard

11 years of experience
450 reviews
Richard
11 years of experience
Chevrolet Cavalier L4-2.2L - Brake Drum - Washington, District of Columbia
Richard both showed up and finished ahead of schedule. He walked me through everything he was going to do, and even saved me money by pointing out one of the parts I thought was broken actually didn't need fixing. Car runs great now.

Alex

22 years of experience
112 reviews
Alex
22 years of experience
Chevrolet Silverado 1500 V8-4.8L - Brake Drum - Apache Junction, Arizona
On time, quick, nice. Will definitely use again!

Patrick

33 years of experience
1435 reviews
Patrick
33 years of experience
Chevrolet Sonic L4-1.8L - Brake Drum - San Marcos, Texas
Excellent job, as always!

Excellent Rating

(10)

Rating Summary
10
0
0
0
0
10
0
0
0
0
Number of Chevrolet Brake Drum Replacement services completed
110+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1600+
experts on our platform

Recent articles & questions

How Long Does an ABS Control Module Last?
Most Most cars that are on the market today have ABS (Anti-lock Brake System). Each manufacturer’s system will vary somewhat, but generally speaking, this is a 4-wheel braking system that prevents your wheels from locking up by modulating the brake...
How Long Does a Courtesy Light Bulb Switch Last?
The The courtesy light bulb switch controls the courtesy light. When you open and close the doors of the vehicle, the courtesy light comes on to allow you to see better. This is both convenient and much safer for you...
The Guide to Legal Car Modifications in Alabama
ARENA Creative / Shutterstock.com Whether you just purchased a new car, recently moved to the state or are just passing through, you need to know whether your modifications are street legal on Alabama roads. For those who...

can a car ventilate without being on?

Hi there. The question you have presented is somewhat confusing. I'm not sure, if you are actually putting a fan inside the car to circulate the air out of the vehicle or the radiator cooling fan runs after the vehicle...

Someone decided to put rocks and dirt in my gas tank I have a 2008 chevy malibu I haven't drove it or turned it

I would definitely not recommend to drive the vehicle in its current condition I would recommend having the gas tank replaced completely not just cleaned. It would be nearly impossible to get all of the rocks out of the tank...

Serpentine tensioner bolt broke off

Unfortunately the only way to resolve this issue would likely be to replace the tensioner as well. If tension cannot be relieved from the belt due to a broken bolt the tensioner will have to be removed completely. If the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com