Chevrolet K2500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet K2500 Brake Drum Replacement is $710 with $254 for parts and $456 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1998 Chevrolet K2500V8-7.4L	Service typeBrake Drum Replacement	Estimate$1061.03	Shop/Dealer Price$1236.31 - $1654.13
1991 Chevrolet K2500V8-7.4L	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.39 - $1558.27
1995 Chevrolet K2500V8-5.7L	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.39 - $1558.26
1988 Chevrolet K2500V8-5.7L	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1137.95 - $1554.35
1990 Chevrolet K2500V6-4.3L	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.46 - $1558.39
1989 Chevrolet K2500V6-4.3L	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1138.06 - $1554.54
1996 Chevrolet K2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$1363.05	Shop/Dealer Price$1631.26 - $2329.16
1999 Chevrolet K2500V8-7.4L	Service typeBrake Drum Replacement	Estimate$1034.47	Shop/Dealer Price$1222.32 - $1675.13

Show example Chevrolet K2500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(28)

Rating Summary

28

0

0

0

0

28

0

0

0

0

SEE REVIEWS NEAR ME

William

30 years of experience

49 reviews

Request William

William

30 years of experience

Request William

by Steve

Chevrolet K2500 V8-5.7L - Car is not starting - Glendale, Arizona

Great guy and the truck is running super!

Chris

20 years of experience

448 reviews

Chris

20 years of experience

by Brett

Chevrolet K2500 V8-5.7L - Water Pump Replacement - Boring, Oregon

Arrived on time, job was done correctly from what I can see right away. Very pleased with this experience and I would try this again.

Jeffrey

27 years of experience

870 reviews

Request Jeffrey

Jeffrey

27 years of experience

Request Jeffrey

by John

Chevrolet K2500 V8-5.7L - Car is not starting - York, South Carolina

I have an older truck that all of a sudden will not start. I was searching for a local mechanic, and stumbled across yourmechanic.com. I saw many positive reviews for Jeffrey Carter, and I had a feeling booking Jeffrey to diagnose the problem may be the right choice. It was 100 percent the right choice. If you are looking for a knowledgeable and personable mechanic you cannot go wrong by booking Jeffrey. Any time I need an auto mechanic I will be booking Jeffrey for as long as he is a yourmechanic.com employee, and I will be recommending Jeffrey to everyone I know.

Daniel

11 years of experience

229 reviews

Daniel

11 years of experience

by James

Chevrolet K2500 V8-7.4L - Check Engine Light is on - Chicago, Illinois

Daniel did a great job. He showed up on time, found everything that was wrong with my vehicle and he explained everything he found.

Excellent Rating

(28)

Rating Summary

28

0

0

0

0

28

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Cell Phones and Texting: Distracted Driving Laws in South Carolina

In In South Carolina, it is illegal for drivers of all ages to text and drive, which includes emails and instant messages. However, there is no statewide ban on the use of handheld or hands free cell phones when making...

Signs You Need a New Car Heater

Car heaters are a key car part for those living in cooler climates. A common sign your car heater isn't working is when air doesn't heat up quickly.

How Do Electric Vehicle Batteries Work?

EV batteries work to power an electric traction motor to move the car’s wheels. Different chemicals produce electricity to provide rechargeable power.

How do I stop my transmission from slipping?

This suggests low transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service) or possibly a faulty transmission control module. A faulty transmission control module may cause a delay in acceleration or erratic shifting of gears. The transmission control module has various sensors such as vehicle speed...

P0401 keeps coming on, already done, cleaned carbon, egr replace, egr tube, pigtail harness.

Claimed by Kevin Gainer

I replaced crank pos. ition sensor I replaced crank position sensor, The car starts after cranking over several times, and the check engine light is still on.

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com