Chevrolet K1500 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(116)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(116)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet K1500 Brake Drum Replacement is $635 with $179 for parts and $456 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1988 Chevrolet K1500V8-5.0LService typeBrake Drum ReplacementEstimate$910.39Shop/Dealer Price$1048.01 - $1352.85
1991 Chevrolet K1500V8-6.2L DieselService typeBrake Drum ReplacementEstimate$824.03Shop/Dealer Price$964.14 - $1276.27
1994 Chevrolet K1500V8-5.7LService typeBrake Drum ReplacementEstimate$816.43Shop/Dealer Price$954.64 - $1261.06
1992 Chevrolet K1500V8-5.0LService typeBrake Drum ReplacementEstimate$824.03Shop/Dealer Price$964.03 - $1276.07
1988 Chevrolet K1500V8-5.7LService typeBrake Drum ReplacementEstimate$814.39Shop/Dealer Price$952.16 - $1257.11
1990 Chevrolet K1500V8-5.7LService typeBrake Drum ReplacementEstimate$824.03Shop/Dealer Price$964.14 - $1276.26
1996 Chevrolet K1500V6-4.3LService typeBrake Drum ReplacementEstimate$840.43Shop/Dealer Price$977.98 - $1283.92
1994 Chevrolet K1500V8-6.5L Turbo DieselService typeBrake Drum ReplacementEstimate$840.43Shop/Dealer Price$979.77 - $1287.05
Show example Chevrolet K1500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(116)

Rating Summary
102
8
3
1
2
102
8
3
1
2

Jeffrey

27 years of experience
870 reviews
Jeffrey
27 years of experience
Chevrolet K1500 V8-5.0L - Oil Change - Lancaster, South Carolina
Very professional and thorough!

John

27 years of experience
1033 reviews
John
27 years of experience
Chevrolet K1500 V8-5.7L - Car is not starting - League City, Texas
Great guy, was on time professional and got my truck back up and running in no time. Would highly recommend and will definitely use John again in the future.

Jeffrey

8 years of experience
24 reviews
Jeffrey
8 years of experience
Chevrolet K1500 V8-5.7L - Power Steering Pressure Hose - Tempe, Arizona
Jeffrey was very nice and seemed knowledgeable. Unfortunately being late both days and ultimately unable to complete the job which will require another mechanic or dealership visit is the reason for the reduced rating.

Victor

35 years of experience
229 reviews
Victor
35 years of experience
Chevrolet K1500 V8-5.7L - Window Motor / Regulator Assembly Replacement (Driver Side Front) - Albuquerque, New Mexico
Very good at what he does.

Excellent Rating

(116)

Rating Summary
102
8
3
1
2
102
8
3
1
2
Number of Chevrolet K1500 services completed
1276+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1600+
experts on our platform

Recent articles & questions

How Long Does an Ignition Coil Last?
The combustion process that happens when your car is cranked is vital in order to get the car moving. In order for...
Disabled Driver Laws and Permits in Delaware
Each Each state has its own specific requirements for disabled drivers. Below are some guidelines for the state of Delaware to help you understand whether you are eligible to receive disabled driver benefits. There are two types of disability permits...
How to Get an Oregon Driver's Permit
The The state of Oregon requires all new drivers under 18 to begin driving with a learner’s permit, in order to practice safe driving under supervision before getting their full driver’s license. To receive the initial learner’s permit, you must...

My oil pressure sending unit is faulty. What is the cost to replace it?

The cost of replacing your oil pressure sensor (https://www.yourmechanic.com/services/oil-pressure-sensor-replacement) will depend on what year and model your Ford is and sometimes the engine type as well. But you should know that oil pressure can be low even with plenty of...

Loss of power esp on hills

This may be a sign of a clogged catalytic converter. As you may already know, the catalytic converter converts toxic exhaust gases into less harmful pollutants that are suitable to be expelled into the atmosphere. When this is clogged, this...

I hit a light post while backing in R shift and my car suddenly accelerated forward and hit another car. How is that possible?

Hi there. Since you are planning to use this type of information to defend your position, I HIGHLY recommend contacting a local mechanical expert to provide you with this information. Without inspecting your vehicle, any explanation on our part would...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com