Chevrolet Cruze Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Cruze Brake Drum Replacement is $345 with $212 for parts and $133 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2016 Chevrolet CruzeL4-1.4L Turbo	Service typeBrake Drum Replacement	Estimate$585.23	Shop/Dealer Price$705.29 - $1033.97
2018 Chevrolet CruzeL4-1.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.31 - $1006.01
2014 Chevrolet CruzeL4-2.0L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.31 - $1006.01
2018 Chevrolet CruzeL4-1.4L Turbo	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.28 - $1005.95
2017 Chevrolet CruzeL4-1.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.33 - $1006.05
2013 Chevrolet CruzeL4-1.8L	Service typeBrake Drum Replacement	Estimate$669.54	Shop/Dealer Price$808.09 - $1176.41
2011 Chevrolet CruzeL4-1.4L Turbo	Service typeBrake Drum Replacement	Estimate$680.04	Shop/Dealer Price$818.31 - $1186.41
2019 Chevrolet CruzeL4-1.4L Turbo	Service typeBrake Drum Replacement	Estimate$594.22	Shop/Dealer Price$717.72 - $1048.97

Show example Chevrolet Cruze Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(697)

Rating Summary

654

22

6

2

13

654

22

6

2

13

SEE REVIEWS NEAR ME

Michael

25 years of experience

199 reviews

Request Michael

Michael

25 years of experience

Request Michael

by Keith

Chevrolet Cruze L4-1.4L Turbo - Window Motor / Regulator Assembly Replacement (Driver Side Front, Passenger Side Front) - Fort Mill, South Carolina

Very friendly and personable. Will differently use him again!

Behrak

9 years of experience

321 reviews

Behrak

9 years of experience

by Jayson

Chevrolet Cruze L4-1.4L Turbo - Valve Cover Gasket - Alpharetta, Georgia

AWESOME JOB! Timely, knowledgeable GREAT CUSTOMER SERVICE!

William

34 years of experience

517 reviews

Request William

William

34 years of experience

Request William

by Ken

Chevrolet Cruze L4-1.8L - Window fell inside the door - Sun City West, Arizona

William is an excellent mechanic who is very professional and knowledgeable. He did a great job on our car!

Ronald

41 years of experience

301 reviews

Ronald

41 years of experience

by Cameron

Chevrolet Cruze L4-1.4L Turbo - Variable Valve Timing (VVT) Solenoid - Houston, Texas

Super friendly, on time and didn't try to freak me out like telling me my cars going to need a new engine just to get a sale. He was very candid and polite. I passed his cards to my colleagues

Excellent Rating

(697)

Rating Summary

654

22

6

2

13

654

22

6

2

13

SEE REVIEWS NEAR ME

Recent articles & questions

How to Buy a Good Quality Shifter Boot

Your Your shift boot is an important part in your car that is attached to our gear stick. This is what you use to shift gears, and it works as a great way to cover the gear assembly. It takes...

How to Replace a Lost or Stolen Car Title in New Mexico

When When it comes to your vehicle one of the most important, if not the most important document you need to keep track of is your car title. This title is what proves you are the registered owner. This makes...

Child Seat Safety Laws in North Dakota

Motor Motor vehicle collisions are one of the most common causes of accidental death for children in North Dakota. Child seats save lives, and not only is it common sense to use them, it is also the law. Summary of...

Brake booster replacement for 2005 Volkswagen Phaeton.

Hi there. You will have to remove the master cylinder and all of the engine components that are in the way of the brake booster. Then the bolts on the inside of the cab will need to be removed to...

I have questions about my 2009 kia spectra's CEL and the codes I had read. Car run's good and was running good when light came on.

Given the three codes (https://www.yourmechanic.com/article/p0170-obd-ii-trouble-code-fuel-trim-malfunction-bank-1-by-andrew-quinn), a known issue with sensor wiring in that vehicle (to be discussed momentarily), and only 89,000 miles on the engine, I would judge the likelihood of sensor failure to be "average". That is, there are...

When I start my car it and try to pull off it shakes and then cut off I was told it was the fuel pressure sensor which I replaced

You will need to have computer scanned for codes and supply the codes you get so I can help you better. The fuel system pressure sensor is an input for the fuel pump control module so it can control the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com