Chevrolet Avalanche 2500 Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Chevrolet Avalanche 2500 Tie Rod End Replacement is $195 with $100 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2004 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Rear Right Inner ReplacementEstimate$315.63Shop/Dealer Price$375.79 - $533.77
2006 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Front Right Outer ReplacementEstimate$295.63Shop/Dealer Price$355.81 - $513.80
2006 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Rear Right Outer ReplacementEstimate$295.63Shop/Dealer Price$355.81 - $513.80
2002 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Rear Left Outer ReplacementEstimate$295.63Shop/Dealer Price$355.79 - $513.76
2002 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Rear Right Inner ReplacementEstimate$295.63Shop/Dealer Price$355.82 - $513.83
2006 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Rear Right Inner ReplacementEstimate$295.63Shop/Dealer Price$355.81 - $513.80
2006 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Rear Left Inner ReplacementEstimate$300.63Shop/Dealer Price$360.67 - $518.56
2004 Chevrolet Avalanche 2500V8-8.1LService typeTie Rod End - Front Right Outer ReplacementEstimate$300.63Shop/Dealer Price$361.04 - $519.22
Show example Chevrolet Avalanche 2500 Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(4)

Rating Summary
3
1
0
0
0
3
1
0
0
0

Jeff

33 years of experience
441 reviews
Jeff
33 years of experience
Chevrolet Avalanche 2500 V8-8.1L - Oil Change - Elk Grove, California
Professional and was on time Very pleased and will use again.

Faraz

22 years of experience
81 reviews
Faraz
22 years of experience
Chevrolet Avalanche 2500 V8-8.1L - Transfer case fluid is low - Pleasanton, California
Great experience!

Peter

43 years of experience
1321 reviews
Peter
43 years of experience
Chevrolet Avalanche 2500 V8-8.1L - Battery - Tempe, Arizona
Peter was on time and promtply dealt with the battery replacemnet and did a fair assesment of the vehicle. The vehicle started prompltly and he found it to be in fine working order.

Vladimir

10 years of experience
214 reviews
Vladimir
10 years of experience
Chevrolet Avalanche 2500 V8-8.1L - camshaft position sensor pigtail - Elk Grove, California
Vladimir is very knowledgeable with electrical systems and has been a great mechanic for my vehicle. He often goes above and beyond to help diagnose or fix any issues. Such a pleasure working with someone that knows what he's talking about and can help explain the issues or give advice on how to resolve your issues. His availability is top notch and he even makes the trek to where you are to help. Can't say enough about his workmanship and professionalism.

Excellent Rating

(4)

Rating Summary
3
1
0
0
0
3
1
0
0
0
Number of Chevrolet Avalanche 2500 services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1600+
experts on our platform

Recent articles & questions

The Best Used Cars to Buy If You're a Carpenter
If If you're a carpenter, and working for someone else, the best used car is whatever you like that gets you to work on time and holds your tools – in short, practically any used car will do. If you...
How to Buy Good Quality Windows
High High quality windows on your vehicle not only make visibility better, but they provide a safety factor. Today’s modern vehicles all feature glass that is strong and breaks differently than typical glass. For the sake of this story, we’ll...
How To Add Air To Your Tires
Checking and adding air pressure to your tires requires finding the proper tire pressure, a good gauge, and an air compressor with a tire chuck.

Bleach in gas tank 2010 Nissan Maxima

Hello - this problem will require the fuel system to be completely drained, flushed with fresh fuel and drained, then refilled with fresh fuel. Change the fuel filter AFTER the first flush with fresh fuel to be sure all bleach...

Motor Mount

Motor mounts will allow the motor to move too much when accelerating. If you feel motor move when you give it gas and may hear clunk. The motor mounts should be checked. If engine runs rough it may be something...

Most of my lights on the dashboard besides engine light are lit up and also there is a little moisture around the transfer case and oil plug.

The dash lights could be on for a loose or broken ground wire to the chassis. Check all of the ground wires on the chassis and make sure that they are tight and clean. The moisture on the transfer case...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com