Cadillac Eldorado Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Cadillac Eldorado Brake Drum Replacement is $294 with $190 for parts and $104 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1974 Cadillac EldoradoV8-8.2L	Service typeBrake Drum Replacement	Estimate$733.90	Shop/Dealer Price$890.38 - $1265.33
1983 Cadillac EldoradoV8-4.1L	Service typeBrake Drum Replacement	Estimate$539.41	Shop/Dealer Price$667.43 - $1008.08
1996 Cadillac EldoradoV8-4.6L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.59 - $1062.12
1998 Cadillac EldoradoV8-4.6L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.52 - $1062.00
1984 Cadillac EldoradoV8-5.7L Diesel	Service typeBrake Drum Replacement	Estimate$596.21	Shop/Dealer Price$738.45 - $1121.73
1985 Cadillac EldoradoV8-4.1L	Service typeBrake Drum Replacement	Estimate$539.41	Shop/Dealer Price$667.42 - $1008.08
1969 Cadillac EldoradoV8-7.7L	Service typeBrake Drum Replacement	Estimate$690.44	Shop/Dealer Price$844.55 - $1213.53
1972 Cadillac EldoradoV8-8.2L	Service typeBrake Drum Replacement	Estimate$697.90	Shop/Dealer Price$855.44 - $1231.19

Show example Cadillac Eldorado Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Cadillac mechanics

Real customer reviews from Cadillac owners like you.

Excellent Rating

(122)

Rating Summary

115

2

1

1

3

115

2

1

1

3

SEE REVIEWS NEAR ME

Leslie

14 years of experience

81 reviews

Leslie

14 years of experience

by brian

Cadillac Eldorado V8-8.2L - Car is not starting - Claymont, Delaware

Honest and knowledgable.

Brent

8 years of experience

58 reviews

Brent

8 years of experience

by Chris

Cadillac Eldorado V8-4.6L - Engine is misfiring - Atlanta, Georgia

Brent was professional, fast and quite knowledgeable

James

31 years of experience

694 reviews

James

31 years of experience

by Patricia

Cadillac Eldorado V8-4.6L - Alternator - Anaheim, California

He was on time, very nice and the car is running fine so far.

Scott

36 years of experience

902 reviews

Scott

36 years of experience

by John

Cadillac Eldorado V8-4.5L - Heater Hose - Mesa, Arizona

Scott's experience is penultimate - he knew what to do, and how to do it - on top of that he is a great guy, a hard worker, and takes pride in his work - bottom line Scott is the best mechanic I have ever met.

Excellent Rating

(122)

Rating Summary

115

2

1

1

3

115

2

1

1

3

SEE REVIEWS NEAR ME

Recent articles & questions

Is It Safe to Drive With the Overdrive Light On?

The overdrive (O/D) light on your dash can mean two very different things, depending on whether it is lighting up and staying on,...

P2529 OBD-II Trouble Code: Vacuum Reservoir Press Sensor Circuit Intermmittent

P2529 code means the vacuum reservoir pressure sensor is not sending an input signal due to a defective vacuum sensor, pump, hose, valve, or a leak.

P0324 OBD-II Trouble Code: Knock Control System Error

Trouble code P0324 means the powertrain control module (PCM) detects an incorrect voltage reading from the knock sensor circuit.

Would like to get an estimate cost to swap my engine with a 2JZGTE Motor and to do it without converting my car from a FWD to RWD

Hello. The engine swap you are inquiring about would require heavy customization, and for this reason is not a service we would be able to provide. The 2JZGTE is a rear wheel drive motor, designed to be longitudinally mounted, and...

My cars RPMs rev up and down

Hello, and thank you for writing in. Typically when the engine behaves like this, you are looking at an air issue. You will want to focus in on the air intake, mainly the throttle and throttle position sensor. You may...

Hello oil control valve timing solenoid issues

Sometimes you can solve a P0011 by replacing the solenoid, but that is not exactly what the code is for. The code is simply saying that the camshaft timing is too far advanced. The VVT system has some control over...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com