Buick Reatta Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(7)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(7)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Buick Reatta Brake Drum Replacement is $341 with $218 for parts and $123 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1990 Buick ReattaV6-3.8LService typeBrake Drum ReplacementEstimate$608.41Shop/Dealer Price$732.39 - $1070.58
1991 Buick ReattaV6-3.8LService typeBrake Drum ReplacementEstimate$578.41Shop/Dealer Price$702.41 - $1040.63
1988 Buick ReattaV6-3.8LService typeBrake Drum ReplacementEstimate$597.40Shop/Dealer Price$723.41 - $1063.13
1989 Buick ReattaV6-3.8LService typeBrake Drum ReplacementEstimate$559.41Shop/Dealer Price$681.38 - $1018.07
Show example Buick Reatta Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Buick mechanics

Real customer reviews from Buick owners like you.

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0

Kiri

20 years of experience
372 reviews
Kiri
20 years of experience
Buick Reatta V6-3.8L - Car is not starting - Ambler, Pennsylvania
Good

Joshua

27 years of experience
709 reviews
Joshua
27 years of experience
Buick Reatta V6-3.8L - 1. passenger side headlight doesn't open, what will it cost fix (INSPECTION of headlight door not opening) - Suisun City, California
finally a mechanic a single woman can trust and be treated with respect...Joshua Floyd put me at ease and answered all my questions without making me feel stupid...when it's time to fix the problems that come my way with my car, I'll be calling and asking for Joshua to help me fix it...

Stephen

25 years of experience
48 reviews
Stephen
25 years of experience
Buick Reatta V6-3.8L - Parking / Emergency Brake does not work - Summerville, South Carolina
Very well informative and descriptive mechanic

Andrew

9 years of experience
41 reviews
Andrew
9 years of experience
Buick Reatta V6-3.8L - Brake Pads Replacement (Front, Rear) - Houston, Texas
On time and warm and friendly took care of repairs within short time frame.

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0
Number of Buick Reatta services completed
77+
services done by our mechanics
TOTAL NUMBER OF EXPERT Buick MECHANICS
800+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Idler Pulley
Common signs include a damaged bearing or pulley, squealing from the engine area, and visibly worn pulleys.
How Long Does an Axle / CV Shaft Assembly Last?
Axle Axle shafts, or CV (constant velocity) shafts, are essentially long metal poles that connect the wheels of your car to the transmission gears, and allows the wheels to rotate. The transmission works to rotate the axle shafts, which in...
How to Buy a Personalized License Plate in Montana
A A personalized license plate (https://www.yourmechanic.com/article/how-to-find-out-which-license-plates-are-available-in-your-state-by-brady-klopfer) is an excellent way to add a little bit of unique flair to your vehicle. With a personalized plate, you can say something about yourself through your car and show off some of your...

My blinde spot monitor and Driver Assist are off and they will not let me turn them back on. I have two messages saying they neede

The car wash could just be coincidental to the failure or it could represent a source of water intrusion in an electrical connector and that has caused the two systems to malfunction. The two systems are electrical in nature and...

when I open my door my interior lights won’t turn on.

You may have a problem with the interior lighting module or light switch is in wrong position. You will need to have the system scanned using a scanner that can see the interior light module and all the different door...

I have an 07 Ford explorer and I changed the fuel pump and driver module but fuel pump driver module getting power but no power to the pump

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com