BMW Z3 Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(73)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(73)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a BMW Z3 Power Steering Pressure Hose Replacement is $374 with $234 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1998 BMW Z3L6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$966.16Shop/Dealer Price$1175.25 - $1788.35
2002 BMW Z3L6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$957.15Shop/Dealer Price$1163.15 - $1773.93
2001 BMW Z3L6-2.5LService typePower Steering Pressure Hose ReplacementEstimate$957.15Shop/Dealer Price$1163.19 - $1774.00
2001 BMW Z3L6-3.2LService typePower Steering Pressure Hose ReplacementEstimate$977.43Shop/Dealer Price$1188.54 - $1814.56
1998 BMW Z3L4-1.9LService typePower Steering Pressure Hose ReplacementEstimate$1044.59Shop/Dealer Price$1265.87 - $1912.65
2000 BMW Z3L6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$957.15Shop/Dealer Price$1163.44 - $1774.43
1997 BMW Z3L6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$957.15Shop/Dealer Price$1163.22 - $1774.05
2001 BMW Z3L6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$957.15Shop/Dealer Price$1163.19 - $1774.00
Show example BMW Z3 Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(73)

Rating Summary
72
1
0
0
0
72
1
0
0
0

David

17 years of experience
639 reviews
David
17 years of experience
BMW Z3 L6-2.5L - Oil Change - Antioch, California
He was well-versed in his craft. Took his time to do the job & rechecked his own work. Was very clean and efficient!!!

Jose

11 years of experience
58 reviews
Jose
11 years of experience
BMW Z3 L6-2.5L - Alternator - Fresno, California
Great job!

Shawn

13 years of experience
379 reviews
Shawn
13 years of experience
BMW Z3 L6-3.0L - Alternator - Chester Springs, Pennsylvania
Great job. Did my alternator and explained a lot.

Brandon

19 years of experience
318 reviews
Brandon
19 years of experience
BMW Z3 L6-2.8L - AC is not working - Chapel Hill, North Carolina
Brandon came on time and did all work as needed.

Excellent Rating

(73)

Rating Summary
72
1
0
0
0
72
1
0
0
0
Number of BMW Z3 services completed
803+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

The Best Tool For Mechanics to Check for Intake Vacuum/Boost Pressure Leaks
Automotive technician jobs require tools to check for engine leaks. Mac Tools has a high pressure smoke machine that finds leaks in car components.
P0432 OBD-II Trouble Code: Main Catalyst Efficiency Below Threshold (Bank 2)
Trouble code P0432 means the catalytic converter in engine bank 2 is working below efficiency.
How to Buy a Good Quality Cylinder Head
The The cylinder head is one of the single most critical parts of your car’s mechanics, and one part that can trigger the most engine damage if it becomes compromised. The cylinder head, along with the head gasket, sits on...

Car shaking when applying brakes and going slow. Check Engine Light is on and engine idles roughly.

It sounds like you may have a vacuum leak on your car. Check all vacuum lines and make sure they are in good condition and connected. If you don't see a leak you can spray some carburetor cleaner on the...

Starting problems on a 2005 Honda Pilot

If it cranks but it doesn't start, I've got a video "fixing the car that cranks but doesn't start (https://www.youtube.com/watch?v=064Ilsz8Fzg)." You'd want to do all those tests. Check the fuel pump pressure and check if you are getting spark to...

Air conditioner pump making noise and no cold air. No power coming to pump in 2011 Nissan Rogue

Hey there, thank you for asking about your 2011 Nissan Rogue. When the compressor pump starts to make noise, combined with not blowing cool air, there are many possible problems. It is quite possible that the compressor itself has frozen....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com