BMW ActiveHybrid 3 Fuel Injector Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5)

Fuel Injector Replacement Service

How much does a Fuel Injector Replacement cost?

On average, the cost for a BMW ActiveHybrid 3 Fuel Injector Replacement is $1353 with $863 for parts and $490 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2013 BMW ActiveHybrid 3L6-3.0L Turbo HybridService typeFuel Injector ReplacementEstimate$4198.86Shop/Dealer Price$5135.00 - $7893.81
2015 BMW ActiveHybrid 3L6-3.0L Turbo HybridService typeFuel Injector ReplacementEstimate$2236.53Shop/Dealer Price$2679.15 - $3981.74
2014 BMW ActiveHybrid 3L6-3.0L Turbo HybridService typeFuel Injector ReplacementEstimate$2236.53Shop/Dealer Price$2679.30 - $3982.01
Show example BMW ActiveHybrid 3 Fuel Injector Replacement prices

What is a fuel injector and how does it work?

A fuel injector is a fuel metering device that sprays atomized droplets of fuel in a specific pattern into the engine’s intake manifold or directly into the combustion chamber. The injector has a solenoid and valve within and the operation, or pulsing, of the solenoid is controlled by the powertrain control module (PCM). The PCM controls the solenoid’s “on” time in order to keep the air-fuel ratio optimized while the engine load and operating conditions constantly change. Fuel injectors are usually connected to a fuel rail located on the top of the engine and the fuel rail, in turn, is supplied with fuel under pressure from the fuel pump located in the fuel tank.

When to consider replacing a fuel injector:

  • Rough idle, loss of power, or misfiring. Poor engine operation has many causes but faults in the fuel injection system, including the fuel injectors, are high on the list of possibilities.
  • Odor of raw gas or visible leaks. Fuel injectors should not leak fuel into the intake manifold when the car is off. If you notice any fuel odor around your car, the possibility of a leaking fuel injector should be considered. There should be no external leak from a fuel injector. If an externally-leaking injector is suspected, do not start your car due to the fire hazard.
  • Check engine light. Some fuel injection failures, for example, a faulty solenoid, may cause a trouble code to be set in the PCM and that will cause the check engine light to illuminate. The codes are read and the fuel injector is tested directly, as needed.
  • Major engine repairs, engine replacement, or lengthy storage. All fuel injectors will have deposits given enough mileage. These deposits can cause an imbalance in the performance of the injectors from cylinder to cylinder. When an engine is already disassembled, or if you are installing a new engine, that is a perfect time to service the injectors as a set. All injectors have tiny internal filter baskets. A professional injector service facility will clean each injector ultrasonically and replace these filters for a relatively low cost.

How do mechanics replace a fuel injector?

Injectors can be serviced once removed from the car or replaced outright with new injectors. If the injectors are serviced, specialized cleaning and test equipment are required. The choice to repair versus replace will depend on exactly what is wrong with the injector as well as customer preference. Either option requires removing the injector from the car and the following procedure is typical:

  • Once the engine is cold, the pressure within the fuel rail is relieved by briefly running the engine with the fuel pump fuse out.
  • The upper plenum on the intake manifold is removed along with any cables, hoses, or wiring that restricts access.
  • The supply and return lines are removed from the fuel rail. The electrical connectors to each fuel injector are unlocked and removed. The fuel rail is then unbolted and removed from the intake manifold.
  • The injector(s) requiring replacement are removed from the fuel rail, taking care to not allow any debris to enter the exposed openings. An O-ring seal usually holds the injector very firmly in a finely polished bore in the fuel rail.
  • Using a new O-ring, the serviced or replaced injector is re-inserted into the fuel rail — using engine oil on the O-ring to prevent damaging it. O-rings in this application fit very tight to prevent fuel leaks.
  • The fuel rail is re-installed and the supply and return lines are re-connected. The plenum is re-installed along with all cables, hoses, or wiring.
  • Finally, the engine is run, there is a careful check for leaks, and the vehicle is road tested.

Is it safe to drive with a fuel injector problem?

Yes, so long as there is no external leak of fuel from a broken or malfunctioning injector, it is safe to drive the car. However, if the injector is known to be malfunctioning, it can cause engine misfires, excessive emissions or, in the case of a badly leaking injector, can overload and overheat the catalytic converter. Additionally, fuel efficiency will always be diminished if the fuel injectors are not working properly.

When replacing a fuel injector keep in mind:

  • Using high quality (Tier One) gasoline may reduce deposits on fuel injectors and prolong their life.
  • If an injector problem develops that requires removal of one injector, the best practice is to remove and service all of the injectors at the same time. That service might involve replacement of the electrically failed injector along with off-the-car cleaning of the remaining injectors. Serving all injectors at once ensures the injector set will be balanced, in terms of flow rates, and in turn promote smooth operation of the engine.
  • Do not use fuel system cleaning compounds, or procedures, unless such materials are specified by the manufacturer of your car.
  • On the car cleaning of fuel injectors is not as effective as off-the-car cleaning because injectors have tiny internal filter baskets that should be replaced as part of the process of servicing a fuel injector.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(5)

Rating Summary
4
1
0
0
0
4
1
0
0
0

Joe

44 years of experience
838 reviews
Joe
44 years of experience
BMW ActiveHybrid 3 L6-3.0L Turbo Hybrid - Pre-purchase Car Inspection - Tampa, Florida
Straight forward, there was a delay because of another appointment running over but he gave me a heads up way ahead of time.

Kevin

25 years of experience
651 reviews
Kevin
25 years of experience
BMW ActiveHybrid 3 L6-3.0L Turbo Hybrid - Car Battery Replacement - Atlanta, Georgia
Kevin was friendly and knowledgeable.

Raymond

38 years of experience
613 reviews
Raymond
38 years of experience
BMW ActiveHybrid 3 L6-3.0L Turbo Hybrid - Oil Change - Las Vegas, Nevada
Very professional and proficient. He also did the work in a timely matter as well. Highly recommend him.

Patrick

16 years of experience
406 reviews
Patrick
16 years of experience
BMW ActiveHybrid 3 L6-3.0L Turbo Hybrid - Brake Pads Replacement (Front) - Chester, Virginia
Very nice worked quick

Excellent Rating

(5)

Rating Summary
4
1
0
0
0
4
1
0
0
0
Number of BMW ActiveHybrid 3 services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

P3484 OBD-II Trouble Code: Cylinder 11 Deactivation/Intake Valve Control Circuit High
P3484 code means cylinder 11 was deactivated during certain driving conditions due to low oil pressure, engine condition, or electrical components.
How to Replace a Pitman Arm Shaft Seal
The pitman arm attaches to the steering box via a shaft. To prevent leaks and driveability issues, the pitman arm shaft seal is used on this shaft.
2012 Ford Mustang vs. 2012 Dodge Charger: Which One Should I Buy?
Technically these two vehicles have wildly different classifications: compact for the Ford Mustang and large car for the Dodge Charger. However, who would consider either one anything other than a muscle car? These cars are meant for speed, fun, and...

Car won't start after flooring accelerator while going 75 MPH.

Your Dodge Stratus sounds as if it may be experiencing a serious problem. The initial symptom of the RPMs jumping from maximum to 2000 RPMS, appears to reveal that your transmission has slipped out of gear. The maxing out of...

Poor acceleration

If your car has not had a major service that has involved replacing spark plugs and all the filters that might be all that you need. Mercedes recommends replacing the plugs at 100 k but I prefer to do it...

Transmission stuck in gear in Drive 2007 Chevrolet Silverado 2500

Hi there - it's possible that your problem source is the torque converter lockup clutch (https://www.yourmechanic.com/question/car-hesitates-and-then-jerks-to-go-into-first-gear-by-brenda) NOT releasing as the truck slows down. This would lug the engine as though it's in top gear until vibration, or an engine stop/start...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com