BMW 440i xDrive Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6,607)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6,607)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 440i xDrive Brake Drum Replacement is $457 with $314 for parts and $142 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 BMW 440i xDriveL6-3.0L TurboService typeBrake Drum ReplacementEstimate$823.68Shop/Dealer Price$997.74 - $1481.64
2017 BMW 440i xDriveL6-3.0L TurboService typeBrake Drum ReplacementEstimate$770.69Shop/Dealer Price$942.76 - $1425.19
2018 BMW 440i xDriveL6-3.0L TurboService typeBrake Drum ReplacementEstimate$789.68Shop/Dealer Price$963.76 - $1447.69
Show example BMW 440i xDrive Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(6,607)

Rating Summary
6,159
203
60
44
141
6,159
203
60
44
141

John

6 years of experience
35 reviews
John
6 years of experience
BMW 335xi L6-3.0L Turbo - Serpentine/Drive Belt - Bellevue, Washington
John did a fantastic job working on my car. He really shows that he cares and stands by his work.

Joe

43 years of experience
821 reviews
Joe
43 years of experience
BMW 528i L4-2.0L Turbo - Water Pump Replacement - Tampa, Florida
Changed water pump and coolant on BMW 528i. No issues, great!

Attila

19 years of experience
910 reviews
Attila
19 years of experience
BMW 750i xDrive V8-4.4L Turbo - Check Engine Light is on - Newark, New Jersey
He was on time and knew what the car needed exactly

Behrak

9 years of experience
322 reviews
Behrak
9 years of experience
BMW X1 L4-2.0L Turbo - Oil Change - Atlanta, Georgia
Behrak arrived early and got my oil change completed in 30mins! He’s awesome. Will deff be using him again!

Excellent Rating

(6,607)

Rating Summary
6,159
203
60
44
141
6,159
203
60
44
141
Number of BMW services completed
72677+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Toyota Corolla
Not Not only does the 2012 Toyota Corolla continue to be one of the best-selling compact sedans in the United States, but it also continues to maintain very high resale values. If you want a car that you’ll get your...
How to Buy a Good Quality Cell Phone Car Mount/Holder
Where Where do you set your cell phone when you’re in the car? If you’re looking for a way to have it visible, and not loose in the car, then a cell phone car mount/holder is the ideal option. These...
P0584 OBD-II Trouble Code: Cruise Control Vacuum Control Circuit High
P0584 means an error with the cruise control vacuum control circuit, caused by a faulty cruise control switch, or a defective vacuum supply hose.

What does it mean if cylinder 2 and 6 are not firing and it is not the plug, plug wire, or coil because they have all been changed.

Hello. If the misfires are continuing to occur and the ignition parts are good then it may be a faulty fuel injector or an issue within the engine. I usually do a compression test first. By doing this I would...

My car want start when cold Without acceleration

On a car of this age, make sure all engine maintenance (plugs, wires, filters) is up to date and change the fuel filter. If the difficulty still persists, a hard starting diagnostic (https://www.yourmechanic.com/services/car-is-hard-to-start-inspection), performed by YourMechanic, would identify the issue....

It sounds like a rod knocking and now it wont start at all

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com