BMW 323i Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(3)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(3)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a BMW 323i Water Pump Replacement is $411 with $159 for parts and $252 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1999 BMW 323iL6-2.5LService typeWater Pump ReplacementEstimate$597.60Shop/Dealer Price$688.59 - $936.05
2000 BMW 323iL6-2.5LService typeWater Pump ReplacementEstimate$581.38Shop/Dealer Price$666.81 - $910.09
1998 BMW 323iL6-2.5LService typeWater Pump ReplacementEstimate$581.38Shop/Dealer Price$666.89 - $910.23
Show example BMW 323i Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0
Number of BMW 323i Water Pump Replacement services completed
33+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

How to Use a Steam Cleaner to Detail a Car
Regardless Regardless of how you use your vehicle, the interior can get dirty and soiled over time. Your car can get dirty in any of the following ways: Dyes and dirt transferred to the seats from clothing Oil and dirt...
P0030 OBD-II Trouble Code: HO2S Heater Control Circuit (Bank 1 Sensor 1)
P0030 Trouble code definition P0030 is the code for HO2S Heater Control Circuit (Bank 1 Sensor 1) What the P0030 code means...
The Guide to Right-of-Way Laws in Alaska
Traffic Traffic laws are founded in common sense, and are in place to ensure that traffic moves safely and smoothly. In Alaska, most accidents are due to failure to yield right of way when required by law. “Right-of-way” is the...

Electrical problems, now car won't start.

Consider yourself lucky that you made it home! Most stories like this end on the back of a tow truck, after a few hours waiting on the side of the road. Now, the good news is the symptoms you describe...

Car not shifting correctly

The gear shifting mechanism or cables are causing a problem due to a bad bushing, or lever out of adjustment. If all the cables and bushings are okay, then you possibly have an inside shift fork problem. The cables should...

No tail light, instrument panel light, or tag light

Hi there, thanks for writing in. Most ancillary electrical items (like tail lights, instrument panel lights and tag lights) are actually controlled through an electrical relay box. On your Ford Expedition, there is usually a main relay control box (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-electronic-control-relay)...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com