Audi Cabriolet Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Audi Cabriolet Brake Drum Replacement is $398 with $236 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1995 Audi CabrioletV6-2.8L	Service typeBrake Drum Replacement	Estimate$667.58	Shop/Dealer Price$815.36 - $1191.75
1996 Audi CabrioletV6-2.8L	Service typeBrake Drum Replacement	Estimate$633.58	Shop/Dealer Price$781.42 - $1157.85
1998 Audi CabrioletV6-2.8L	Service typeBrake Drum Replacement	Estimate$633.58	Shop/Dealer Price$781.41 - $1157.84
1994 Audi CabrioletV6-2.8L	Service typeBrake Drum Replacement	Estimate$633.58	Shop/Dealer Price$781.34 - $1157.72
1997 Audi CabrioletV6-2.8L	Service typeBrake Drum Replacement	Estimate$633.58	Shop/Dealer Price$781.46 - $1157.92

Show example Audi Cabriolet Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Audi mechanics

Real customer reviews from Audi owners like you.

Excellent Rating

(2,467)

Rating Summary

2,288

87

19

12

61

2,288

87

19

12

61

SEE REVIEWS NEAR ME

Stephen

32 years of experience

182 reviews

Request Stephen

Stephen

32 years of experience

Request Stephen

by Emily

Audi Cabriolet V6-2.8L - Car is not starting - Westminster, Colorado

He was able to diagnosed the problem, and able to fix ed my car. He's the only one, in fact. Thank you Stephen.

Brikk

18 years of experience

389 reviews

Brikk

18 years of experience

by Kip

Audi Cabriolet V6-2.8L - Window is not working - Charlotte, North Carolina

Brick is very thorough and makes sure he does the job right.

Joe

20 years of experience

126 reviews

Joe

20 years of experience

by Fred

Audi Q7 V6-3.6L - Battery - Riverdale, Illinois

Joe was on time. Installed the new battery on my 2007 Audi Q7 v6 and did thorough inspection of coding the battery. He also checked the oil, and other fluid levels. He was totally professional and left no mess.

Duane

25 years of experience

527 reviews

Duane

25 years of experience

by Daniel

Audi Allroad Quattro V8-4.2L - Air Spring Bag Replacement (Driver Side Rear, Passenger Side Rear) - Cardiff By The Sea, California

Duane is the man. He goes above and beyond to help out and make you feel comfortable. He is much more thorough than some of the indie shops I have been to. He takes the time do things like use using gauges to measure play in bushings as compared to indie shops that try to feel it by hand.

Excellent Rating

(2,467)

Rating Summary

2,288

87

19

12

61

2,288

87

19

12

61

SEE REVIEWS NEAR ME

Recent articles & questions

How Long Does an AC Control Switch Last?

Every Every year, vehicles become more and more complex, with computer components replacing mechanical parts. This is very apparent in your car’s air conditioning system, which relies on an AC control module to deliver the ideal heating and air conditioning...

How to Register a Car in New Jersey

Making Making sure that your car is registered when moving to the state of New Jersey is very important. While there are a number of other things that you will have to worry about during the moving process, the registering...

How to Use a BMW With Comfort Access Technology

The The BMW comfort access technology was introduced in 2002 as a keyless remote system that uses sensors to detect where the owner is in proximity to the vehicle within 1.5 meters (about 5 feet), allowing him or her to...

Can't get an emissions test due to faulty plug

Hi! Since the power fuse was blown and your attempts to install a new fuse causes sparks, it would seem that there is a large draw or short on that power system. First, disconnect the ground cable to the battery...

How bad is it to repair a ball joint and CV axle?

You are looking at a lengthy repair. There are several components that will need to be replaced. It is hard to say how rough the removal and installation of these parts will be, because the amount of damage that has...

Engine light on code P0401

Assuming that the passageways, including any through and within the plenum and intake are truly completely clear, there is likely a problem with other EGR system components. On your vehicle, Diagnostic Trouble Code P0401 (https://www.yourmechanic.com/article/p0401-obd-ii-trouble-code-exhaust-gas-recirculation-flow-malfunction-by-jay-safford) involves not just blocked passageways...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com