Acura RSX Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Acura RSX Brake Drum Replacement is $323 with $209 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2004 Acura RSXL4-2.0L	Service typeBrake Drum Replacement	Estimate$555.63	Shop/Dealer Price$681.04 - $1010.02
2003 Acura RSXL4-2.0L	Service typeBrake Drum Replacement	Estimate$531.63	Shop/Dealer Price$657.08 - $986.09
2002 Acura RSXL4-2.0L	Service typeBrake Drum Replacement	Estimate$560.13	Shop/Dealer Price$690.83 - $1023.78
2006 Acura RSXL4-2.0L	Service typeBrake Drum Replacement	Estimate$531.63	Shop/Dealer Price$657.03 - $986.00
2005 Acura RSXL4-2.0L	Service typeBrake Drum Replacement	Estimate$531.63	Shop/Dealer Price$657.11 - $986.14

Show example Acura RSX Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Acura mechanics

Real customer reviews from Acura owners like you.

Excellent Rating

(184)

Rating Summary

173

3

3

2

3

173

3

3

2

3

SEE REVIEWS NEAR ME

Jeffrey

27 years of experience

870 reviews

Request Jeffrey

Jeffrey

27 years of experience

Request Jeffrey

by Savannah

Acura RSX L4-2.0L - Car is not starting - Pineville, North Carolina

On time to appointment - actually 30 minutes early. Always goes above and beyond to meet my needs. I never consider taking my car elsewhere since meeting him.

Khoa

20 years of experience

402 reviews

Khoa

20 years of experience

by Mary

Acura RSX L4-2.0L - Check Engine Light is on - San Jose, California

Khoa contacted me earlier to see if he could come out earlier to my appointment which was great! I had two of the low beam bulbs so he deducted that from my cost. Khoa worked through the two tasks quick in a hour and was able to explain the diagnosis and answer my questions.

Jason

32 years of experience

515 reviews

Jason

32 years of experience

by Cory

Acura RSX L4-2.0L - Starter - Tucson, Arizona

Jason was a great guy and completed work quickly.

Jean

25 years of experience

70 reviews

Jean

25 years of experience

by Jay

Acura RSX L4-2.0L - Pre-purchase Car Inspection - Duluth, Georgia

Everything was great except he was over an hour late for the appointment. I was there to get him started, and I had the keys, but I was on my lunch break. I was late going back to work, that was not good. His inspection was excellent though, saved us a lot of cash!

Excellent Rating

(184)

Rating Summary

173

3

3

2

3

173

3

3

2

3

SEE REVIEWS NEAR ME

Recent articles & questions

What Does It Mean When My Car Is "Burning" Oil?

Burning oil is usually caused by leaking oil that burns up on hot engine or exhaust components. Fix leaking oil to prevent expensive car repairs.

How to Buy Sport Shocks

Shock Shock absorbers (https://www.yourmechanic.com/article/3-essential-things-to-know-about-your-car-s-shock-absorbers) help lessen the bumps you encounter while driving down the road. They do this by absorbing some of the energy created by driving across a rough patch of road, over speed bumps, or other road obstructions....

How to Obtain an A7 ASE Study Guide and Practice Test

Automotive technician jobs pay more if you’re ASE certified. Get study guides & practice tests for an A7 Heating & Air Conditioning Repair Technician

idle is high after driving

Hey there. Normally a vacuum leak is the most common cause of a high idle but many issues may cause this. Other possible causes of a high idle are improper sensor inputs, an idle air control valve, a faulty engine...

my car vibrate when accelerate

Well, first I hope you're not actually driving 120 mph in your 2004 Toyota Camry. Most engine shaking issues while under acceleration are caused by loose motor mounts (https://www.yourmechanic.com/services/engine-mount-replacement) or stabilizer bar bushings (https://www.yourmechanic.com/services/stabilizer-bar-bushings-replacement). It can also be caused by...

I have a 2008 dodge avenger. 2.7. V6. Morning. Run great once warmed up. It starts to misfire n runs very rough. Already changed

Hi Christopher. Typically when an engine misfiring issue occurs after the engine has come to operating temperature, it's due to fuel related components, such as fuel injectors that are clogged or misfiring themselves. This could be due to excessive carbon...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com