Volvo S60 Cross Country Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(1,461)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(1,461)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Volvo S60 Cross Country Brake Drum Replacement is $411 with $250 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2018 Volvo S60 Cross CountryL4-2.0L TurboService typeBrake Drum ReplacementEstimate$726.04Shop/Dealer Price$875.69 - $1286.36
2016 Volvo S60 Cross CountryL5-2.5L TurboService typeBrake Drum ReplacementEstimate$660.52Shop/Dealer Price$802.32 - $1189.37
2017 Volvo S60 Cross CountryL4-2.0L TurboService typeBrake Drum ReplacementEstimate$692.04Shop/Dealer Price$841.71 - $1252.41
Show example Volvo S60 Cross Country Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Volvo mechanics

Real customer reviews from Volvo owners like you.

Excellent Rating

(1,461)

Rating Summary
1,372
47
10
5
27
1,372
47
10
5
27

Albert

22 years of experience
81 reviews
Albert
22 years of experience
Volvo S40 L5-2.4L - Electrical components are not working - Snellville, Georgia
Mr. Dujinski was very professional.

Jeff

33 years of experience
441 reviews
Jeff
33 years of experience
Volvo XC90 L5-2.5L Turbo - Inspection / Diagnostics - Rio Linda, California
I must say... if you need a mechanic, look no further than Your Mechanic.com

Brian

23 years of experience
661 reviews
Brian
23 years of experience
Volvo XC90 V8-4.4L - shift cable repairs - Jacksonville, Florida
Brian is dependable, consistent, and goes the extra mile to ensure that the job is done well.

Adam

29 years of experience
95 reviews
Adam
29 years of experience
Volvo XC90 L6-3.2L - Car will not turn over - San Antonio, Texas
Adam is an A plus mechanic and a wonderful, dedicated, and customer first worker. He takes the time and puts forth the effort to ensure all issues are resolved and your vehicle is once again running smoothly. I would highly recommend Adam for any automotive concerns.

Excellent Rating

(1,461)

Rating Summary
1,372
47
10
5
27
1,372
47
10
5
27
Number of Volvo services completed
16071+
services done by our mechanics
TOTAL NUMBER OF EXPERT Volvo MECHANICS
600+
experts on our platform

Recent articles & questions

How Do Spare Tires Differ From Regular Tires?
Unless Unless you drive one of the select few vehicles that are equipped with a full-size matching spare tire, your spare tire is not the same as the other four that are on your vehicle. There are significant manufacturing differences...
How to Buy a Good Quality Fuel Injector
Getting Getting fuel directly to an engine is accomplished through an electronic fuel injector; with each cylinder getting its own dose of fuel which is much more efficient than the ways carburetors would send fuel directly to the engine in...
P2667 OBD-II Trouble Code: Fuel Shutoff Valve B Control Circuit High
P2667 means there is a problem with the fuel shut off valve usually after a rear end collision or other electrical issues or problem.

Car not charging

A starting charging test should definitely be carried out. This will reveal whether or not the battery has been drained and needs replacement. This also checks the starter for proper operation and cranking voltage. The alternator will be tested checking...

Engine not getting any fuel

Hi there. Your vehicle's fuel pump needs to prime/whine when the ignition is turned into the on position. If you do not hear this humming noise it can mean you have a faulty fuel relay or fuel pump itself. Another...

Loss all power when driving.

What you describe sounds like a charging system failure. If the alternator isn't working, the car can run on the battery for a period of time, until the battery voltage gets below a certain point, usually around 10.5 volts. After...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com