Toyota RAV4 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(1,164)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(1,164)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Toyota RAV4 Brake Drum Replacement is $304 with $190 for parts and $114 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2012 Toyota RAV4V6-3.5LService typeBrake Drum ReplacementEstimate$634.43Shop/Dealer Price$766.79 - $1132.37
2013 Toyota RAV4L4-2.5LService typeBrake Drum ReplacementEstimate$576.22Shop/Dealer Price$698.31 - $1028.52
2000 Toyota RAV4L4-2.0LService typeBrake Drum ReplacementEstimate$654.54Shop/Dealer Price$783.84 - $1115.42
1998 Toyota RAV4L4-2.0LService typeBrake Drum ReplacementEstimate$617.48Shop/Dealer Price$737.46 - $1041.20
1998 Toyota RAV4ElectricService typeBrake Drum ReplacementEstimate$916.44Shop/Dealer Price$1111.26 - $1639.29
2008 Toyota RAV4V6-3.5LService typeBrake Drum ReplacementEstimate$606.43Shop/Dealer Price$738.81 - $1104.41
2010 Toyota RAV4L4-2.5LService typeBrake Drum ReplacementEstimate$613.43Shop/Dealer Price$745.62 - $1111.08
2009 Toyota RAV4V6-3.5LService typeBrake Drum ReplacementEstimate$613.43Shop/Dealer Price$746.14 - $1111.99
Show example Toyota RAV4 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Toyota mechanics

Real customer reviews from Toyota owners like you.

Excellent Rating

(1,164)

Rating Summary
1,107
30
7
4
16
1,107
30
7
4
16

Eugenio

26 years of experience
133 reviews
Eugenio
26 years of experience
Toyota RAV4 L4-2.4L - Check Engine Light is on - Oakton, Virginia
Great service fast and reliable

Shaun

21 years of experience
204 reviews
Shaun
21 years of experience
Toyota RAV4 L4-2.4L - Alternator - Concord, California
Got the job done early, and took a look at the other items I need to have worked on.

Carlos

12 years of experience
77 reviews
Carlos
12 years of experience
Toyota RAV4 L4-2.5L - Oil Change - Whittier, California
Really nice dude! I always like to ask for advice on various things and Carlos answered everything.

Jermaine

24 years of experience
246 reviews
Jermaine
24 years of experience
Toyota RAV4 L4-2.0L - Electrical components are not working - Silver Spring, Maryland
This was my UTMOST BEST!!!! Experience dealing with all the mechanics in my lifetime!!0 He was able to diagnose the problem immediately and took care of it right away. I will NEVER used anyone else in future, only your company. I am beyond happy. Thank you so much!!!!!!!!!

Excellent Rating

(1,164)

Rating Summary
1,107
30
7
4
16
1,107
30
7
4
16
Number of Toyota RAV4 services completed
12804+
services done by our mechanics
TOTAL NUMBER OF EXPERT Toyota MECHANICS
1600+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Expansion Valve (Orifice Tube)
Common signs include the AC system working worse than usual, frost coming from the vents, or the AC compressor constantly running.
How Long Does a Low Oil Level Sensor Last?
Having Having the right amount of oil in an engine is important to the smooth running of your engine. In order for the engine on a car to run as intended, it will have to have the right amount of...
P0472 OBD-II Trouble Code: Exhaust Pressure Sensor Low
P0472 code means there is a problem with your electrical circuit, often due to issues with the back pressure sensor.

How does the driver’s side window switch work?

The driver’s side window switch in your car is the master control for the entire system. You can operate each window from this one switch (it’s connected by wires to the window motors in each door). There are also additional...

Shaking while stopped, difficult acceleration, sudden takeoff

It sounds like you may be experiencing an engine misfire. When a cylinder in your engine is misfiring, it will throw off the balance of the running engine. As a result, vibrations can be felt throughout the vehicle. This would...

How do I get the lower clamp off the radiator hose on the driver side? I can't fit anything in to squeeze It

Hi there, thanks for writing in. I'd be happy to help. The squeeze clamp may require a flexible squeeze clamp tool to get it off, if you can't get it off with a hose clamp (https://www.yourmechanic.com/article/the-best-tool-to-reach-hose-clamps-by-timothy-charlet). Hope this helps and...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com