Subaru Tribeca Front Crankshaft Seal Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(24)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(24)

Front Crankshaft Seal Replacement Service

How much does a Front Crankshaft Seal Replacement cost?

On average, the cost for a Subaru Tribeca Front Crankshaft Seal Replacement is $157 with $17 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2014 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$189.74Shop/Dealer Price$202.03 - $230.78
2011 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$180.73Shop/Dealer Price$191.25 - $218.68
2013 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$180.73Shop/Dealer Price$191.27 - $218.72
2008 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$180.73Shop/Dealer Price$191.27 - $218.72
2012 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$180.73Shop/Dealer Price$192.75 - $221.30
2010 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$180.73Shop/Dealer Price$191.41 - $218.97
2009 Subaru TribecaH6-3.6LService typeFront Crankshaft Seal ReplacementEstimate$180.73Shop/Dealer Price$191.29 - $218.75
Show example Subaru Tribeca Front Crankshaft Seal Replacement prices

What is the Front Crankshaft Seal all about?

A number of mechanisms must work together to make your vehicle move forward. One of the most important is the crankshaft, which converts rotary into linear motion; i.e., it transforms the force created by the engine's pistons moving up and down into a force that moves in a circular motion that causes a car’s wheel to turn. Enclosed in what’s called a crankcase—the largest cavity in the engine block, just below the cylinders—the crankshaft must be completely lubricated, essentially submerged in oil, to spin nearly friction-free and do its job properly.

Consequently, there are seals located at either end of the crankshaft that allow it to spin freely and keep engine oil from escaping the engine block, as well as prevent contaminants and other debris from entering and causing damage to the mechanism. Since there are two ends of the crankshaft, there are two types of seals: the front crankshaft seal and the rear crankshaft seal, also known as the front main and rear main seals.

Keep in mind:

  • Loss of oil will eventually cause serious internal engine damage.
  • Inspect the sealing surface of the crankshaft or the crankshaft pulley (depending on the engine design) for damage when replacing the crankshaft seal.
  • Oil degrades rubber components.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The crankshaft damper and timing belt is removed
  • The crankshaft seal is removed and a new one installed
  • The timing belt and cover along with crankshaft damper is reinstalled
  • The engine accessory belts are installed and the vehicle is lowered off of the jack stands

Our recommendation:

One of the most important parts of your car, crankshaft seals are typically made from a durable material, such as a synthetic rubber or silicone, designed to handle the extreme pressure and temperatures as well as the caustic chemicals in your engine oil. Because they are exposed to such abuse, main seals are subject to a lot of wear and tear. And whether you are talking a front or rear main seal, replacement is the only cure when one malfunctions.

The good news is that the seals are relatively inexpensive components. The bad news is that neither is easy to replace.

Front seal: The front seal is located behind the main pulley that drives all the belts, which is, of course, always spinning. The main pulley throws any leaking oil out in a big circle. It can get thrown up on the alternator, steering pump, belts, in short anything attached to the front of the engine and cause a real mess and eventually some serious damage. Consequently, it has to be removed along with many of the components attached to the front of the block to replace the front main seal.

Rear seal: The rear crankshaft seal is placed along with the transmission; therefore, the process of replacing it requires the removal of transmission, as well as the clutch and flywheel assembly. This is a very involved job.

What common symptoms indicate you may need to replace the Front Crankshaft Seal?

  • Oil leaking from the front crank pulley.
  • Oil dripping from the bottom of the clutch housing, where the block and transmission meet.
  • Clutch slip caused by oil spraying on the clutch.

How important is this service?

Letting either crankshaft seal continue to leak can be detrimental to your vehicle’s continued operation. Besides the maladies caused by driving around with little to no oil flowing in the engine, the faulty seal will be spread oil through the engine bay and undercarriage of your car as you drive, a mess that is difficult to clean up and can be a fire hazard. Replacing is better addressed sooner than later.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Subaru mechanics

Real customer reviews from Subaru owners like you.

Excellent Rating

(24)

Rating Summary
23
0
0
1
0
23
0
0
1
0

Miguel

22 years of experience
273 reviews
Miguel
22 years of experience
Subaru Tribeca H6-3.6L - Pre-purchase Car Inspection - Little Ferry, New Jersey
Miguel Was Very Knowledgeable and patient and answered all my questions. I learned A lot from his diagnostic and Test drive. I will Want to use him again for my next Pre purchase diagnostic in the near future.

Dante

37 years of experience
98 reviews
Dante
37 years of experience
Subaru Tribeca H6-3.6L - UberX Inspection and Oil Change Package - Huntington Beach, California

Rob

20 years of experience
24 reviews
Rob
20 years of experience
Subaru Tribeca H6-3.6L - Pre-purchase Car Inspection - Parsippany, New Jersey
Was very professional and kept me up to date with the pre purchase inspection ( I was not present at the time of inspection) happy with it, however there was a couple of things missed, but in his defence, it was day time so it was very hard to notice it (passenger side puddle light was out)

Alexander

7 years of experience
126 reviews
Alexander
7 years of experience
Subaru Tribeca H6-3.6L - Serpentine/Drive Belt - Dublin, Ohio
Professional experienced and great communication. Clearly able to identify the problem and fix it quickly. Thank you so much Alexander.

Excellent Rating

(24)

Rating Summary
23
0
0
1
0
23
0
0
1
0
Number of Subaru Tribeca services completed
264+
services done by our mechanics
TOTAL NUMBER OF EXPERT Subaru MECHANICS
800+
experts on our platform

Recent articles & questions

Do You Need an Extended Warranty?
When When purchasing a vehicle, dealerships usually offer an extended warranty (https://www.yourmechanic.com/article/how-to-use-your-car-warranty-successfully-by-patrick-haas). While an extended warranty may not be necessary when buying a new vehicle, they usually come in handy if you buy a used vehicle. When determining if you...
A Buyer’s Guide to the 2012 Mitsubishi i-MiEV
Cute Cute pretty much sums up the 2012 Mitsubishi i-MiEV. It’s a super compact electric car capable of driving for quite some distance on battery power alone. However, the lack of a gasoline engine means that you might not want...
P0338 OBD-II Trouble Code: Crankshaft Position Sensor A Circuit High Input
P0338 P0338 code definition The P0338 Trouble Code indicates an error with the crankshaft position sensor A circuit high input. What the P0338 code means The powertrain control module has found that the crankshaft position sensor (https://www.yourmechanic.com/services/crankshaft-position-sensor-replacement), or CPS, is...

cut off while driving and running rough

Hello there, many different faults will cause your 1999 Dodge Grand Caravan to run poorly and shut off. The most common would be the spark plugs, plug wires, coil, fuel pump, fuel filter, alternator, vacuum leak, battery, wiring harness fault...

Replace the front wheel bearings. Can I remove the bearing assembly without having to detach the lower ball joint?

The wheel hub assembly can come off with taking off the three bolts that secure it to the knuckle on the vehicle. You do not need to remove the lower ball joint to remove the wheel hub assembly. If you...

New battery. Car won't start until minutes later when attempted again.

A voltage test will not reveal whether the battery is defective or not. A different test, referred to as a "load test" (https://www.yourmechanic.com/services/battery-is-dead-inspection), is required. During these no start incidents, check to see if the engine immobilizer system (security system)...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com