Ram ProMaster 2500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Ram ProMaster 2500 Brake Drum Replacement is $395 with $233 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2018 Ram ProMaster 2500V6-3.6L	Service typeBrake Drum Replacement	Estimate$915.80	Shop/Dealer Price$1112.89 - $1665.88
2015 Ram ProMaster 2500L4-3.0L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$665.54	Shop/Dealer Price$807.22 - $1191.66
2014 Ram ProMaster 2500L4-3.0L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$665.54	Shop/Dealer Price$807.21 - $1191.66
2014 Ram ProMaster 2500V6-3.6L	Service typeBrake Drum Replacement	Estimate$665.54	Shop/Dealer Price$807.17 - $1191.59
2015 Ram ProMaster 2500V6-3.6L	Service typeBrake Drum Replacement	Estimate$665.54	Shop/Dealer Price$807.24 - $1191.71
2019 Ram ProMaster 2500V6-3.6L	Service typeBrake Drum Replacement	Estimate$853.60	Shop/Dealer Price$1043.66 - $1575.53
2017 Ram ProMaster 2500L4-3.0L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$872.10	Shop/Dealer Price$1062.92 - $1595.35
2017 Ram ProMaster 2500V6-3.6L	Service typeBrake Drum Replacement	Estimate$872.10	Shop/Dealer Price$1063.59 - $1596.52

Show example Ram ProMaster 2500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Ram mechanics

Real customer reviews from Ram owners like you.

Excellent Rating

(7)

Rating Summary

7

0

0

0

0

7

0

0

0

0

SEE REVIEWS NEAR ME

David

10 years of experience

193 reviews

David

10 years of experience

by Solmon

Ram ProMaster 2500 V6-3.6L - Alternator - Mount Laurel, New Jersey

david is awesome , fixed my problem with alternator, friendly and professional

Andrew,

5 years of experience

161 reviews

Request Andrew,

Andrew,

5 years of experience

Request Andrew,

by Nicole

Ram ProMaster 2500 V6-3.6L - Pre-purchase Car Inspection - Arlington, Texas

Joaquin Andrew is an amazing mechanic. We would’ve been in a world of problems that was allegedly “under warranty” had Joaquin not checked our vehicles. He is extremely knowledgeable and a really nice, trustworthy guy. We can not thank him enough for his inspections and will definitely recommend him to others. Do not purchase a car first without him checking it first.

Jonathan

35 years of experience

484 reviews

Request Jonathan

Jonathan

35 years of experience

Request Jonathan

by Drew

Ram ProMaster 2500 V6-3.6L - Brake Pads Replacement (Front) - Tampa, Florida

On time / early, done well within expectations and as far as I can tell did a great job at the task to replace the brake pads. Provided insight on other issues and was upbeat about getting it done. Made for a most welcome experience with YourMechanic.

Robert

20 years of experience

1092 reviews

Robert

20 years of experience

by Michael

Ram ProMaster 2500 V6-3.6L - Car is not starting - Denver, Colorado

Quick, responsive and solved the issue quickly!

Excellent Rating

(7)

Rating Summary

7

0

0

0

0

7

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How Serious Is It When a Hose Is Leaking?

A leaking hose in your car could indicate different problems. Some leaking hoses are more serious than others, but all should be checked and repaired.

How Does a Fuel Injection Flush Work?

Fuel Fuel injectors, as their name implies, are responsible for getting fuel into the engine. Fuel injection systems either work via a throttle body containing as few as 2 injectors, or go straight into the port with one injector per...

How to Install an LCD Monitor in Your Car

Monitors are installed in the console, mounted on the ceiling, or wired into the headrests of a car. LCD monitors provide entertainment or GPS help.

I've got codes P0171 P0102 P0113 P0171 P0101 from the CEL and TRAC being lit up. This happened all of a sudden and the 2010 Toyot

Hi there. The codes P0171 (System too lean bank1), P0102 (mass airflow circuit low), P0113 (intake air temperature circuit high), and P0101 (mass airflow circuit range/performance) could be, all related to a faulty MAF (mass airflow) sensor (https://www.yourmechanic.com/services/mass-airflow-sensor-replacement). The TRAC...

Air con not working and my car overheating but everything fill up

The air conditioning and engine cooling systems are diagnosed separately. The cause of no A/C can be determined through a non functioning A/C diagnostic (https://www.yourmechanic.com/services/ac-is-not-working-inspection). Engine overheating typically occurs if the engine cooling thermostat has failed, the water pump, or...

I just had a new alternator belt put in now I here a very loud rattling nose , what could it be? It gets louder when I excelerat

Hi there. If this happened right after the belt was installed then it probably has something to do with that installation. However, there is the possibility of a simple coincidence; things can happen and parts do fail. I would have...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com