Plymouth Colt Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Plymouth Colt Brake Drum Replacement is $373 with $145 for parts and $228 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1989 Plymouth ColtL4-1.5L	Service typeBrake Drum Replacement	Estimate$721.85	Shop/Dealer Price$849.83 - $1170.74
1989 Plymouth ColtL4-1.8L	Service typeBrake Drum Replacement	Estimate$665.85	Shop/Dealer Price$793.88 - $1114.83
1987 Plymouth ColtL4-1.6L Turbo	Service typeBrake Drum Replacement	Estimate$613.05	Shop/Dealer Price$727.87 - $1009.22
1989 Plymouth ColtL4-2.0L	Service typeBrake Drum Replacement	Estimate$665.85	Shop/Dealer Price$793.81 - $1114.71
1990 Plymouth ColtL4-1.5L	Service typeBrake Drum Replacement	Estimate$666.39	Shop/Dealer Price$794.59 - $1115.98
1993 Plymouth ColtL4-1.5L	Service typeBrake Drum Replacement	Estimate$518.06	Shop/Dealer Price$614.62 - $850.21
1994 Plymouth ColtL4-2.4L	Service typeBrake Drum Replacement	Estimate$598.13	Shop/Dealer Price$705.34 - $964.71
1978 Plymouth ColtL4-2.0L	Service typeBrake Drum Replacement	Estimate$710.08	Shop/Dealer Price$852.21 - $1223.24

Show example Plymouth Colt Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Plymouth mechanics

Real customer reviews from Plymouth owners like you.

Excellent Rating

(156)

Rating Summary

143

5

1

1

6

143

5

1

1

6

SEE REVIEWS NEAR ME

Nate

21 years of experience

90 reviews

Nate

21 years of experience

by Kimberley

Plymouth Colt L4-1.5L - Car is not starting - Austell, Georgia

Jason

17 years of experience

429 reviews

Jason

17 years of experience

by Chuck

Plymouth Colt L4-1.5L - Oil or Fluid is leaking - San Jose, California

Excellent mechanic!! Get's an A+ from us. Quality work, very personable. Would not hesitate to use him again!! (Forgot to put a rating in right after the work was done, so I am doing it now. The repair was done a while ago.... still running great with no problems. Fixed the problem and after all this time is still running well!!)

Chris

20 years of experience

448 reviews

Chris

20 years of experience

by Jeff

Plymouth Acclaim V6-3.0L - Brake Drum - Vancouver, Washington

Chris was fast and friendly. While I hope I won't need him again, he will be the guy who comes back to fix my daughters car.

Vladimir

10 years of experience

214 reviews

Request Vladimir

Vladimir

10 years of experience

Request Vladimir

by Richard

Plymouth Neon L4-2.0L - Control Arm Assembly Replacement (Front Lower Right) - Sacramento, California

Great guy, easy to talk to and went above and beyond what he had to do. Would recommend definitely.

Excellent Rating

(156)

Rating Summary

143

5

1

1

6

143

5

1

1

6

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2012 Ford Taurus

The The Ford Taurus received something of a revival over the past several years, and it has become one of the family sedan staples in the United States. It’s a beautiful and bold looking vehicle that offers a wealth of...

Is It Safe to Drive With a Bent Axle?

Your car’s axles are essential components. They transmit power from the transmission or differential to the drive wheels. While they’re designed to be...

How to Find Out Which License Plates are Available in Your State

When When you register your vehicle, you get a license plate. Unless you specify otherwise, you will get the standard, generic license plate for your state. However, most states have numerous options for fun, specialized license plates. Some of these...

Whining noise over 60 mph on a 2007 BMW

You went to the wrong mechanic. It's whining and it is not supposed to whine. A good mechanic can analyze it. This could've been beyond their knowledge or they don't know much about BMW. Watch my video, "how to find...

Cooling

Fill the reservoir with water and look to see where it is leaking from. The reservoir is an easy item to replace if that's what is leaking. You may also need to open the radiator cap to properly fill the...

Squeal when engine starts or revs.

With having already replaced the belt and the idler and tensioner, I would look at the components next. Something like the bearing or bushing going out in one of the other driven components. The alternator, the power steering pump, or...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com