Mercury Monterey Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(19)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(19)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Mercury Monterey Tie Rod End Replacement is $143 with $48 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1964 Mercury MontereyV8-7.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$283.87Shop/Dealer Price$336.09 - $470.25
1963 Mercury MontereyV8-7.0LService typeTie Rod End - Rear Right Inner ReplacementEstimate$263.87Shop/Dealer Price$316.11 - $450.28
1966 Mercury MontereyV8-6.4LService typeTie Rod End - Rear Left Inner ReplacementEstimate$263.87Shop/Dealer Price$316.11 - $450.28
2006 Mercury MontereyV6-4.2LService typeTie Rod End - Rear Left Inner ReplacementEstimate$190.69Shop/Dealer Price$224.61 - $303.88
1960 Mercury MontereyV8-7.0LService typeTie Rod End - Rear Left Inner ReplacementEstimate$263.87Shop/Dealer Price$316.12 - $450.31
1970 Mercury MontereyV8-7.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$257.27Shop/Dealer Price$307.86 - $437.08
1972 Mercury MontereyV8-7.0LService typeTie Rod End - Front Right Inner ReplacementEstimate$268.87Shop/Dealer Price$320.97 - $455.04
1974 Mercury MontereyV8-6.6LService typeTie Rod End - Rear Right Inner ReplacementEstimate$268.87Shop/Dealer Price$321.34 - $455.70
Show example Mercury Monterey Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(19)

Rating Summary
19
0
0
0
0
19
0
0
0
0

Jeff

13 years of experience
46 reviews
Jeff
13 years of experience
Mercury Monterey V6-4.2L - Car is not starting - Reisterstown, Maryland
He communicated well upon scheduling and when he would arrive for the appointment. He was thorough and explained his diagnosis of the problem. Highly recommend.

Norberto

14 years of experience
6 reviews
Norberto
14 years of experience
Mercury Monterey V6-4.2L - Spark Plugs - Austell, Georgia
I love that you tell us not only about what you fix, but also what we need to GET fixed. 10/10 Highly Recommended

Scott

22 years of experience
49 reviews
Scott
22 years of experience
Mercury Monterey V6-4.2L - Car is making a noise - Phoenix, Arizona
Very thorough. Explained things to me as he was doing them. I trusted him enough to leave him to his work, and he was done in about 75-80 minutes. Seems to be an honest guy. I would have him work on my van again.

Krystal

17 years of experience
106 reviews
Krystal
17 years of experience
Mercury Monterey V6-4.2L - Brake System Flush - Chicago, Illinois
As usual, Krystal was very prompt, professional, and, pleasant.

Excellent Rating

(19)

Rating Summary
19
0
0
0
0
19
0
0
0
0
Number of Mercury Monterey services completed
209+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

Symptoms of Bad or Failing Intake Manifold Gaskets
Common signs include the engine constantly overheating, coolant leaking, engine misfires, and a decrease in power, acceleration, and fuel economy.
How to Park in Reverse
It It is unavoidable that at some point, soon after you start driving, you will need to reverse into a parking space. At times you will find yourself in a tight position where the only options are to back into...
How to Clean and Maintain Windshield Washers
When When dirt or debris lands on your windshield while driving, your immediate reaction would be to use the wiper fluid spray to clear it. If your car’s wiper fluid doesn't spray properly, it may have clogged wiper fluid nozzles...

Power steering warninglight on off

Hi there. Most of the time, the power steering warning light is illuminated when there is a mechanical or electrical issue that triggers an error code and then illuminates the light on the dash. In other cases, it can illuminate...

I have code P1120 in my pcm I replaced the throttle position sensor cleared the code and it came back less than a month later

The throttle body should be inspected for binding and dirt but there are quite a few other reasons why the code ended up returning, namely: the throttle position sensor harness is open or shorted; the throttle position sensor circuit has...

Carfax shows minor damage no airbag deployed. Is it ok to buy?

Carfax reports unfortunately only reflect any work or damage that was reported to Carfax. I would suggest checking the Kelly Blue Book website with specifics related to your zip code as market prices of cars vary by zip code. This...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com