Mercedes-Benz SL550 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz SL550 Brake Drum Replacement is $346 with $213 for parts and $133 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2010 Mercedes-Benz SL550V8-5.5L	Service typeBrake Drum Replacement	Estimate$727.76	Shop/Dealer Price$891.71 - $1320.55
2008 Mercedes-Benz SL550V8-5.5L	Service typeBrake Drum Replacement	Estimate$559.31	Shop/Dealer Price$690.43 - $1028.58
2019 Mercedes-Benz SL550V8-4.7L Turbo	Service typeBrake Drum Replacement	Estimate$732.56	Shop/Dealer Price$892.36 - $1333.45
2013 Mercedes-Benz SL550V8-4.7L Turbo	Service typeBrake Drum Replacement	Estimate$1533.50	Shop/Dealer Price$1894.88 - $2943.01
2011 Mercedes-Benz SL550V8-5.5L	Service typeBrake Drum Replacement	Estimate$653.11	Shop/Dealer Price$807.10 - $1209.82
2018 Mercedes-Benz SL550V8-4.7L Turbo	Service typeBrake Drum Replacement	Estimate$732.56	Shop/Dealer Price$892.36 - $1333.45
2017 Mercedes-Benz SL550V8-4.7L Turbo	Service typeBrake Drum Replacement	Estimate$731.06	Shop/Dealer Price$889.64 - $1329.81
2016 Mercedes-Benz SL550V8-4.7L Turbo	Service typeBrake Drum Replacement	Estimate$731.06	Shop/Dealer Price$890.24 - $1330.86

Show example Mercedes-Benz SL550 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(36)

Rating Summary

35

0

0

1

0

35

0

0

1

0

SEE REVIEWS NEAR ME

Frank

40 years of experience

57 reviews

Frank

40 years of experience

by Karl

Mercedes-Benz SL550 V8-5.5L - Pre-purchase Car Inspection - Marietta, Georgia

Very professional and was able to arrive prior to appointment time.....I will use him in the future.

John

20 years of experience

568 reviews

John

20 years of experience

by milo

Mercedes-Benz SL550 V8-5.5L - Battery - Orlando, Florida

John is the Best ! Showed Up On Time, Answered All My Questions And Fixed The Issue !

Nicholas

13 years of experience

35 reviews

Request Nicholas

Nicholas

13 years of experience

Request Nicholas

by Voltaire

Mercedes-Benz SL550 V8-5.5L - Auxiliary Battery - Bonita, California

Nicholas did a great job on my SL550! I'm not a car guy so he took the time to answer a bunch of questions I had while he continued working. He made some recommendations for me that I will be sure to follow up with him in the future. Quick and easy!

Cody

8 years of experience

99 reviews

Cody

8 years of experience

by Mark

Mercedes-Benz SL550 V8-5.5L - Headlight Bulb Replacement (Driver Side Low Beam) - Fort Worth, Texas

Cody was great. He was on time and completed the job quickly. I'd would have him work on my car anytime! Thanks.

Excellent Rating

(36)

Rating Summary

35

0

0

1

0

35

0

0

1

0

SEE REVIEWS NEAR ME

Recent articles & questions

Is a Kinked Hose Still Safe to Use?

Hoses Hoses carry fluids from one point in your engine to another. For example, the upper radiator hose carries hot water into the radiator from the engine, while the lower radiator hose moves cooled coolant out of the radiator into...

How Often Should Brakes Be Replaced?

Brake pads and brake rotors wear out over time. How long brakes last depends on the brake material, as well as your driving patterns.

How Do I Prepare My Car for Summer?

Summer's Summer's heat, dust, and stop-and-go traffic will take their tolls on your vehicle. Follow these tips to ensure optimum wellness of your car: Air Conditioning: Have your air conditioning inspected (https://www.yourmechanic.com/services/heating-ac-inspection) by a qualified technician. Newer models have cabin...

What should I know about rotating my tires?

Proper tire care involves quite a few things. You need to check the tire pressure regularly. You need to inspect the tread for wear. You need to check for damage to the sidewalls. You also need to make sure the...

Intermittent starting issues

Hello. There are two easy ways to test a starter. One is to measure the voltage present at the starter terminals when cranking the vehicle. Another way is to test the starter with a starting system tester directly at the...

rear door lock jammed

From what you've described, it sounds like the door latch may have been jammed when the lock and handle was actuated at the same time. The door panel will have to be removed from the inside by removing the rear...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com