Mercedes-Benz C43 AMG Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Mercedes-Benz C43 AMG Tie Rod End Replacement is $147 with $52 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1998 Mercedes-Benz C43 AMGV8-4.3LService typeTie Rod End - Rear Left Inner ReplacementEstimate$415.23Shop/Dealer Price$508.93 - $638.14
1998 Mercedes-Benz C43 AMGV8-4.3LService typeTie Rod End - Front Left Inner ReplacementEstimate$361.23Shop/Dealer Price$455.05 - $584.34
2018 Mercedes-Benz C43 AMGV6-3.0L TurboService typeTie Rod End - Front Left Outer ReplacementEstimate$343.53Shop/Dealer Price$415.68 - $609.60
2018 Mercedes-Benz C43 AMGV6-3.0L TurboService typeTie Rod End - Rear Right Inner ReplacementEstimate$411.21Shop/Dealer Price$500.26 - $744.92
1998 Mercedes-Benz C43 AMGV8-4.3LService typeTie Rod End - Rear Right Outer ReplacementEstimate$368.53Shop/Dealer Price$464.27 - $599.11
2000 Mercedes-Benz C43 AMGV8-4.3LService typeTie Rod End - Rear Right Inner ReplacementEstimate$361.23Shop/Dealer Price$455.04 - $584.33
1999 Mercedes-Benz C43 AMGV8-4.3LService typeTie Rod End - Rear Left Outer ReplacementEstimate$382.03Shop/Dealer Price$476.75 - $610.82
2018 Mercedes-Benz C43 AMGV6-3.0L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$416.21Shop/Dealer Price$505.52 - $750.38
Show example Mercedes-Benz C43 AMG Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(6)

Rating Summary
6
0
0
0
0
6
0
0
0
0

Adam

17 years of experience
243 reviews
Adam
17 years of experience
Mercedes-Benz C43 AMG V6-3.0L Turbo - Pre-purchase Car Inspection - West Palm Beach, Florida
Fantastic. Very thorough and responded quickly to questions. Highly recommend!

John

27 years of experience
1057 reviews
John
27 years of experience
Mercedes-Benz C43 AMG V6-3.0L Turbo - 40,000 Miles Maintenance Service - Seabrook, Texas
Great guy. Very helpful. I will use him again

Jerry

30 years of experience
48 reviews
Jerry
30 years of experience
Mercedes-Benz C43 AMG V8-4.3L - Windshield Washer Pump Replacement (Front) - Las Vegas, Nevada
Jerry did a great job. we ended up needing one more part, so the job is not totally complete. But he did great.

Jeremy

20 years of experience
642 reviews
Jeremy
20 years of experience
Mercedes-Benz C43 AMG V8-4.3L - Oil/Fluid Leak - Delray Beach, Florida
Very honest, knowledegable and friendly guy. He's a car buff too and will talk about his cars!

Excellent Rating

(6)

Rating Summary
6
0
0
0
0
6
0
0
0
0
Number of Mercedes-Benz C43 AMG services completed
66+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Oil Cooler Hose (Automatic Transmission)
Common signs include visible damage on the hose, oil leaking around the fittings, transmission overheating, and deterioration in the rubber.
How Long Does an Emergency Parking Brake Cable Last?
Your Your emergency parking brake is something all vehicles come with. It consists of an emergency/parking brake cable which connects the parking brake shoes to the parking brake lever. This steel cable is very thin and it runs under your...
10 Best Stores to Buy Auto Parts in Louisville, Kentucky
Automotive technicians rely on auto parts stores to add and replace car parts. The best auto parts shop in Louisville is NAPA Auto Parts.

i changed the left low beam bulb and it still wont work. is there a fuse that i should try changing?

The headlights on the vehicle are HID or high intensity discharge lights and use a different wiring set up from traditional lighting used for years. Your left and right lights are powered by separate power circuits to keep from overheating...

does defective ball joint affect the operation of alternator?

Your ball joint will have nothing to do with the alternator at all. The ball joint is part of the lower control arm of the vehicles suspension and steering. The alternator is mounted on the engine and is used to...

Where can i find a 12" air cleaner cover cover

If this is the factory air cleaner assembly then I suggest looking for it on ebay or at a salvage yard. Otherwise you would need to replace the entire unit with an aftermarket one.

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com