Lincoln Navigator Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Lincoln Navigator Brake Drum Replacement is $332 with $208 for parts and $123 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1998 Lincoln NavigatorV8-5.4L	Service typeBrake Drum Replacement	Estimate$634.15	Shop/Dealer Price$778.07 - $1158.63
1999 Lincoln NavigatorV8-5.4L	Service typeBrake Drum Replacement	Estimate$608.15	Shop/Dealer Price$752.11 - $1132.70
2019 Lincoln NavigatorV6-3.5L Turbo	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.71 - $1023.61
2018 Lincoln NavigatorV6-3.5L Turbo	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.67 - $1023.54
2004 Lincoln NavigatorV8-5.4L	Service typeBrake Drum Replacement	Estimate$646.14	Shop/Dealer Price$797.16 - $1183.04
2006 Lincoln NavigatorV8-5.4L	Service typeBrake Drum Replacement	Estimate$646.14	Shop/Dealer Price$797.11 - $1182.96
2013 Lincoln NavigatorV8-5.4L	Service typeBrake Drum Replacement	Estimate$654.64	Shop/Dealer Price$805.21 - $1190.75
2011 Lincoln NavigatorV8-5.4L	Service typeBrake Drum Replacement	Estimate$654.64	Shop/Dealer Price$806.31 - $1192.69

Show example Lincoln Navigator Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Lincoln mechanics

Real customer reviews from Lincoln owners like you.

Excellent Rating

(290)

Rating Summary

272

10

3

0

5

272

10

3

0

5

SEE REVIEWS NEAR ME

Rodric

14 years of experience

414 reviews

Rodric

14 years of experience

by JOSEPH

Lincoln Navigator V8-5.4L - Serpentine/Drive Belt - Fairburn, Georgia

Excellent performance.

Scott

34 years of experience

548 reviews

Scott

34 years of experience

by David

Lincoln Navigator V6-3.5L Turbo - Oil Change - Westminster, Colorado

Really good guy and performed excellent work!

Tagharchi

23 years of experience

81 reviews

Request Tagharchi

Tagharchi

23 years of experience

Request Tagharchi

by Raymond

Lincoln Navigator V8-5.4L - Hazard / Turn Signal Flasher - Vista, California

Kevin was great! He showed up on time. Went right to work. Fixed my problems and was picked up the packaging. Great job and I will insist he comes again when I next use Your Mechanic.

Shane

17 years of experience

224 reviews

Shane

17 years of experience

by clifton

Lincoln Navigator V8-5.4L - Battery Terminal Ends - Austin, Texas

Good Job, very efficient and clear about his work.

Excellent Rating

(290)

Rating Summary

272

10

3

0

5

272

10

3

0

5

SEE REVIEWS NEAR ME

Recent articles & questions

How to Buy a Car Like a Pro

Most Most people are only aware of two ways of buying a car: from a dealer or through a private sale. There is another way: one that can be quite beneficial if you are flexible in your new vehicle’s options,...

How to Park in Reverse

It It is unavoidable that at some point, soon after you start driving, you will need to reverse into a parking space. At times you will find yourself in a tight position where the only options are to back into...

P2517 OBD-II Trouble Code: A/C Refrigerant Press Sensor B Circuit Low

P2517 code means the A/C refrigerant pressure sensor is out of the normal refrigerant level range, a faulty switch, wiring, or connectors.

AC blowing warm air

Hi. The problem your described is an indicator that the coolant fan for the condenser is not working properly. If the fans are working properly, I suggest having the refrigerant pressure check by an EPA certified technician. If you need...

2 coil packs not working

You only need to replace the two bad ones, but be prepared to replace one or more in the near future. The coils are all the same age and all have the same amount of use and seem to fail...

2000 Toyota 4runner-both oxygen sensor replacement

If you input your year, make and model, as well as location (zip code) at YourMechanic's oxygen sensor replacement service page (https://www.yourmechanic.com/services/oxygen-sensor-replacement), the exact written quote you desire will be provided. Generally, after about 100,000 miles of use, it's not...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com