Land Rover LR4 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Land Rover LR4 Brake Drum Replacement is $377 with $263 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2014 Land Rover LR4V6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$663.55	Shop/Dealer Price$815.94 - $1225.86
2012 Land Rover LR4V8-5.0L	Service typeBrake Drum Replacement	Estimate$711.55	Shop/Dealer Price$880.73 - $1333.06
2013 Land Rover LR4V8-5.0L	Service typeBrake Drum Replacement	Estimate$692.55	Shop/Dealer Price$858.22 - $1307.92
2016 Land Rover LR4V6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$756.89	Shop/Dealer Price$938.60 - $1436.52
2011 Land Rover LR4V8-5.0L	Service typeBrake Drum Replacement	Estimate$692.55	Shop/Dealer Price$858.26 - $1307.98
2015 Land Rover LR4V6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$695.27	Shop/Dealer Price$860.38 - $1300.50
2010 Land Rover LR4V8-5.0L	Service typeBrake Drum Replacement	Estimate$645.55	Shop/Dealer Price$797.69 - $1207.42

Show example Land Rover LR4 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Land Rover mechanics

Real customer reviews from Land Rover owners like you.

Excellent Rating

(73)

Rating Summary

63

5

2

1

2

63

5

2

1

2

SEE REVIEWS NEAR ME

Michael

21 years of experience

80 reviews

Request Michael

Michael

21 years of experience

Request Michael

by Tara

Land Rover LR4 V8-5.0L - Door Lock Actuator Replacement (Driver Side Front) - Olympia, Washington

Michael was great. There was a bit of a hiccup with the parts pickup but it worked out.

Harish

27 years of experience

588 reviews

Harish

27 years of experience

by Kristin

Land Rover LR4 V6-3.0L Turbo - Brake Pads Replacement (Rear) - Charlotte, North Carolina

Great experience overall!

Jonathan

13 years of experience

171 reviews

Request Jonathan

Jonathan

13 years of experience

Request Jonathan

by Jim

Land Rover LR4 V6-3.0L Turbo - Brake Pads Replacement (Front, Rear) - Scituate, Massachusetts

Jonathan replaced my brake pads, rotors, and sensors on my LR4 and did an excellent job. If you want the peace of mind knowing you have a good, knowledgeable, honest mechanic - then hire Jonathan every time. I know I will.

Rusty

23 years of experience

514 reviews

Rusty

23 years of experience

by Charles

Land Rover LR4 V8-5.0L - Pre-purchase Car Inspection - Arlington, Texas

Overall for the price, I’m impressed with the inspection. Would be 5 stars, but I wish some details were clearer (thats more the interface, not his fault). Also, it was hard to understand the voice note recording he took.

Excellent Rating

(73)

Rating Summary

63

5

2

1

2

63

5

2

1

2

SEE REVIEWS NEAR ME

Recent articles & questions

How to Report a Vehicle Break-In

Having Having someone go through the contents of your car and take your personal belongings is a huge violation of your privacy. The act of breaking into a home or vehicle with the intent to commit a crime or theft...

10 Best Stores to Buy Auto Parts in Charlotte, North Carolina

Automotive technicians rely on auto parts stores to add and replace car parts. The best auto parts shop in Charlotte is O'Reilly.

P0653 OBD-II Trouble Code: Sensor Reference Voltage “B” Circuit High

P0653 means that control modules notes a fault in the signals from this sensor due to faulty ground wires, control modules, or other circuitry.

Car overheating and not starting.

If the engine has been overheating and got hot enough then you may have caused some serious engine damage causing the engine to no longer start. If it did not get too hot then these may be separate issues. When...

My car shut off while driving and won't start again

It's possible that your timing chain set is so worn out that the engine either "jumped time" or the timing chain (https://www.yourmechanic.com/services/timing-chain-replacement) broke. The starter may be turning the crankshaft over, but the camshaft and valve gear is no longer...

New thermostat new coolant temp sensor car is still going into red and overheating what do i do

You should first see if the electric cooling fan is coming on before it overheats? If they do not come on then the fans needs checked to see what is keeping it from coming on? It may be a fan...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com