Land Rover Discovery Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Land Rover Discovery Brake Drum Replacement is $315 with $201 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1995 Land Rover DiscoveryV8-3.9L	Service typeBrake Drum Replacement	Estimate$639.60	Shop/Dealer Price$780.39 - $1135.79
2000 Land Rover DiscoveryV8-4.0L	Service typeBrake Drum Replacement	Estimate$563.20	Shop/Dealer Price$693.44 - $1017.09
1998 Land Rover DiscoveryV8-4.0L	Service typeBrake Drum Replacement	Estimate$605.60	Shop/Dealer Price$746.44 - $1101.88
2004 Land Rover DiscoveryV8-4.6L	Service typeBrake Drum Replacement	Estimate$563.20	Shop/Dealer Price$693.37 - $1016.96
2002 Land Rover DiscoveryV8-4.0L	Service typeBrake Drum Replacement	Estimate$563.20	Shop/Dealer Price$693.48 - $1017.16
2019 Land Rover DiscoveryV6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$692.04	Shop/Dealer Price$841.71 - $1252.41
1994 Land Rover DiscoveryV8-3.9L	Service typeBrake Drum Replacement	Estimate$614.10	Shop/Dealer Price$754.53 - $1109.67
2017 Land Rover DiscoveryV6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$731.55	Shop/Dealer Price$896.74 - $1364.64

Show example Land Rover Discovery Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Land Rover mechanics

Real customer reviews from Land Rover owners like you.

Excellent Rating

(120)

Rating Summary

112

5

1

0

2

112

5

1

0

2

SEE REVIEWS NEAR ME

Jonathan

35 years of experience

489 reviews

Request Jonathan

Jonathan

35 years of experience

Request Jonathan

by Timothy

Land Rover Discovery V8-4.0L - Brake Pads Replacement (Rear) - Palm Harbor, Florida

Jonathan was on time as usual. He did a professional job installing back brakes.

Ramon

20 years of experience

166 reviews

Ramon

20 years of experience

by David

Land Rover Discovery V8-4.0L - Bleed Brakes - Tucson, Arizona

Ramon did a great job in accessing exactly what my vehicle needed. He finished the job quickly and gave me a recommendation on a few things I will need to do in the future. He is extremely knowledgeable and is now my trusted mechanic! Thank you!

Matthew

11 years of experience

136 reviews

Request Matthew

Matthew

11 years of experience

Request Matthew

by Faz

Land Rover Discovery V8-4.0L - Oil Change - Henderson, Nevada

great professional great knowledge and good tips

Nicholas

11 years of experience

597 reviews

Request Nicholas

Nicholas

11 years of experience

Request Nicholas

by RICH

Land Rover Discovery V8-4.6L - Transmission Fluid Service - Morrisville, North Carolina

Excellent service, as always!!

Excellent Rating

(120)

Rating Summary

112

5

1

0

2

112

5

1

0

2

SEE REVIEWS NEAR ME

Recent articles & questions

How Often Should Hoses Be Replaced?

Your Your engine needs coolant, the power steering rack needs fluid, and the calipers need fluid to squeeze the rotors to stop the car. Most fluids make their way to their destination through hoses. Those hoses are generally made of...

How to Register a Car in Maryland

In In order to get a vehicle registered in Maryland, you will either need to go to the Maryland Vehicle Administration or send in the documents by mail. There is a 60-day grace period when it comes to registering a...

How to Prepare for the Virginia Driver’s Written Test

Before Before you can drive in Virginia, you need to take your driver’s written test so you can then get your learner’s permit and take the road test. You have to remember that driving is a privilege and not a...

Service Engine Soon light staying on.

Evaporative systems seal the tank off from atmosphere and purge through the intake while the engine is running, if the computer senses that one of the valves electrical or mechanical functions aren't appropriate it will set a check engine light...

Engine misfire cylinder 3

The misfire could very possibly be from low compression. You want the compression across all cylinders to be within 10% of each other at most. The compression for number 3 is under that threshold. It could be caused by worn...

Why would the bolts that connect the CV To the wheel come loose

The CV axle end goes through the wheel hub and hub bearing and is held on to the wheel hub by a large nut that is very tightly torqued. There are no bolts involved, only that one nut. The wheel...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com