Hyundai Elantra Coupe Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(21)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(21)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Hyundai Elantra Coupe Brake Drum Replacement is $326 with $212 for parts and $114 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2014 Hyundai Elantra CoupeL4-2.0LService typeBrake Drum ReplacementEstimate$562.23Shop/Dealer Price$680.29 - $1007.47
2013 Hyundai Elantra CoupeL4-1.8LService typeBrake Drum ReplacementEstimate$538.23Shop/Dealer Price$656.31 - $983.51
Show example Hyundai Elantra Coupe Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Hyundai mechanics

Real customer reviews from Hyundai owners like you.

Excellent Rating

(21)

Rating Summary
19
1
0
1
0
19
1
0
1
0

Lucas

21 years of experience
887 reviews
Lucas
21 years of experience
Hyundai Elantra Coupe L4-1.8L - Brake Pads Replacement (Rear) - Canoga Park, California
Lucas is very professional and knowledgeable. I hightly recommend him

Angel

17 years of experience
106 reviews
Angel
17 years of experience
Hyundai Elantra Coupe L4-1.8L - Serpentine/Drive Belt - Miami, Florida
Came on time and fixed problem quickly and efficiently. Friendly and prifessional

Lewis

16 years of experience
118 reviews
Lewis
16 years of experience
Hyundai Elantra Coupe L4-1.8L - Oil Change - Dallas, Texas
Lewis was very punctual, friendly and thorough! He did a great job and was very easy to work with

Napoleon

27 years of experience
147 reviews
Napoleon
27 years of experience
Hyundai Elantra Coupe L4-1.8L - Brake Pads Replacement (Rear) - Inglewood, California
Napoleon was on time, and very professional.

Excellent Rating

(21)

Rating Summary
19
1
0
1
0
19
1
0
1
0
Number of Hyundai Elantra Coupe services completed
231+
services done by our mechanics
TOTAL NUMBER OF EXPERT Hyundai MECHANICS
1300+
experts on our platform

Recent articles & questions

What Are the Benefits of an Aftermarket Exhaust System?
All All cars must have an exhaust system in order to vent gases from the engine. However, your car’s stock exhaust system probably isn’t all it could be. Automakers are required to make a number of trade-offs to ensure that...
Symptoms of a Bad or Failing Alternator
Common signs include having to jump start the car frequently, dim lights when operating the vehicle, or the Battery Light coming on.
How to Renew Your Car Registration in Rhode Island
There There are a number of things that a person will have to do in the state of Rhode Island in order to drive legally. Among the most important things that you will need to do in order to stay...

Engine died, do I have to replace it now?

The noise you are hearing could be one of several problems. The first and easiest to fix would be to use only manufacturer certified oil filters during oil and filter changes. The oil filter used may not have a built-in...

How much offset would I need to fit 16X8 wheels on my 2004 Chevrolet Silverado

Hello. When using a 16X8 wheel on your truck you need to use an offset of 10 mm. This will give you the necessary clearance for the wheel itself. This may not be suitable for the tire that you are...

Would a bad crankcase valve caused by a tune up on my audi a3?

Hi Lisa. Thanks for contacting us today. Having a tune-up would not likely cause damage to a rear crankshaft seal. This typically occurs over time and is due to common wear and tear. It's a hit or miss type of...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com