Honda Crosstour Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Honda Crosstour Brake Drum Replacement is $336 with $222 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2015 Honda CrosstourV6-3.5L	Service typeBrake Drum Replacement	Estimate$581.85	Shop/Dealer Price$704.81 - $1046.71
2015 Honda CrosstourL4-2.4L	Service typeBrake Drum Replacement	Estimate$557.85	Shop/Dealer Price$680.84 - $1022.75
2012 Honda CrosstourV6-3.5L	Service typeBrake Drum Replacement	Estimate$557.85	Shop/Dealer Price$680.83 - $1022.74
2013 Honda CrosstourV6-3.5L	Service typeBrake Drum Replacement	Estimate$557.85	Shop/Dealer Price$680.81 - $1022.70
2012 Honda CrosstourL4-2.4L	Service typeBrake Drum Replacement	Estimate$557.85	Shop/Dealer Price$680.85 - $1022.78
2013 Honda CrosstourL4-2.4L	Service typeBrake Drum Replacement	Estimate$557.85	Shop/Dealer Price$680.83 - $1022.74
2014 Honda CrosstourV6-3.5L	Service typeBrake Drum Replacement	Estimate$563.85	Shop/Dealer Price$686.67 - $1028.46
2014 Honda CrosstourL4-2.4L	Service typeBrake Drum Replacement	Estimate$563.85	Shop/Dealer Price$687.12 - $1029.24

Show example Honda Crosstour Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Honda mechanics

Real customer reviews from Honda owners like you.

Excellent Rating

(47)

Rating Summary

47

0

0

0

0

47

0

0

0

0

SEE REVIEWS NEAR ME

Joseph

25 years of experience

34 reviews

Joseph

25 years of experience

by Maelinda

Honda Crosstour L4-2.4L - Car is not starting - Oakland, California

Very Honest!

Ben

41 years of experience

1436 reviews

Ben

41 years of experience

by Ken

Honda Crosstour V6-3.5L - Knock Sensor - Houston, Texas

On time, excellent work & very thorough.

Chuck

10 years of experience

365 reviews

Chuck

10 years of experience

by David

Honda Crosstour V6-3.5L - Pre-purchase Car Inspection - Grand Prairie, Texas

Chuck was incredible! I had never purchased a used vehicle online before and contacted Chuck to do a pre-purchase inspection. He did everything required and even told me things I didn't think to ask about. I can now buy with confidence, know what is in good condition, what needs immediate attention, and what to look out for over the next 6 to 12 months. In short, the quality and scope of the service provided was over and above the price paid, and I would not hesitate to use Chuck again.

Brandon

20 years of experience

773 reviews

Request Brandon

Brandon

20 years of experience

Request Brandon

by Catherine

Honda Crosstour V6-3.5L - Oil Change - Orlando, Florida

Brandon arrived early, was extremely knowledgeable and professional, and got the job done quickly. I am very impressed, and will ask for him if I need your services again.

Excellent Rating

(47)

Rating Summary

47

0

0

0

0

47

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Get the Highest Resale Value for Your Car

When When it’s time to turn in the old reliable runner you’ve driven for years in exchange for a nice, shiny new car, you’re going to want to get the best possible return on your investment. However, this return can’t...

How to Replace a Lost or Stolen Car Title in Indiana

Without Without a car title, you’re in a tight spot if you decide to sell the car or trade it in on a new one. The same thing applies if you move out of Indiana – you can’t register it...

How to Stop on a Slippery Road Without Anti-Lock Brakes (ABS)

Slippery road conditions can make it hard to avoid obstacles, especially without ABS brakes. Keep control of your vehicle to avoid unexpected objects.

Where is the map sensor located? 2004 Volvo XC90

Hi - the mass air flow meter (MAF) (https://www.yourmechanic.com/article/how-to-buy-a-good-quality-mass-airflow-sensor) is located in between the air cleaner housing, and the engine's intake manifold. It is a black plastic cylinder about the size of a large coffee cup, with an electrical connector...

2005 Chrysler 300c has a code P0406. I believe EGR needs replacing, Don't know if it will make it 25 miles to dealer.

P0406 (https://www.yourmechanic.com/article/p0406-obd-ii-trouble-code-exhaust-gas-recirculation-sensor-a-circuit-high-by-spencer-clayton) involves the EGR system but that may or may not be the only factor causing your rough running condition. Typically, P0406 will set if you have a failed EGR valve, excessive carbon buildup, an open or short in...

My 2005 Corolla will only start by jump. Afr

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com