GMC V2500 Suburban Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC V2500 Suburban Brake Drum Replacement is $691 with $254 for parts and $437 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1990 GMC V2500 SuburbanV8-5.7L	Service typeBrake Drum Replacement	Estimate$1061.03	Shop/Dealer Price$1236.31 - $1654.13
1988 GMC V2500 SuburbanV8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1138.07 - $1554.55
1988 GMC V2500 SuburbanV8-5.7L	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1138.06 - $1554.54
1989 GMC V2500 SuburbanV8-5.7L	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1137.95 - $1554.35
1987 GMC V2500 SuburbanV8-5.7L	Service typeBrake Drum Replacement	Estimate$944.17	Shop/Dealer Price$1117.13 - $1532.16
1991 GMC V2500 SuburbanV8-5.7L	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.39 - $1558.26
1990 GMC V2500 SuburbanV8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$989.03	Shop/Dealer Price$1163.73 - $1581.12
1991 GMC V2500 SuburbanV8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$989.03	Shop/Dealer Price$1165.52 - $1584.25

Show example GMC V2500 Suburban Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(2,942)

Rating Summary

2,783

79

21

9

50

2,783

79

21

9

50

SEE REVIEWS NEAR ME

Jose

16 years of experience

324 reviews

Jose

16 years of experience

by David

GMC C15 V8-5.7L - Brake Drum - Fort Lauderdale, Florida

Good job

Peter

43 years of experience

1321 reviews

Peter

43 years of experience

by BEN

GMC Sierra 1500 V8-5.3L - Brake Drum - Mesa, Arizona

Excellent as always!

Peter

43 years of experience

1321 reviews

Peter

43 years of experience

by Gary

GMC C1500 V8-5.7L - Check Intake Manifold Gasket - Phoenix, Arizona

Informative patient knowledgeable did the job right.

Joshua

27 years of experience

709 reviews

Joshua

27 years of experience

by John

GMC K1500 Suburban V8-5.7L - Fuel Pump - Brentwood, California

Excellent Mechanic

Excellent Rating

(2,942)

Rating Summary

2,783

79

21

9

50

2,783

79

21

9

50

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2012 Mercedes-Benz R-Class

This This non-minivan, non-SUV, non-station wagon is nothing if not a class unto itself. Mercedes classifies it as a crossover but it reps more like a combination of all of the above. Its precise identity is really immaterial however, as...

A Buyer's Guide to the 2012 Volkswagen Beetle

Although Although it may be one of the most recognizable cars on the road, thanks to its unique design, perhaps you’ve never considered owning a Volkswagen Beetle before. There are a number of reasons the 2012 model should have you...

How Long Does a Vacuum Booster Last?

Without Without a properly working braking system, it will be nearly impossible to avoid being in a wreck. Most people fail to realize just how important their braking system is until they are without it due to repair issues. In...

I have a dent right where you open the door so if I suck the dent out will the door open

If the door stopped opening properly after the dent happened, then it's fairly safe to assume that the dent is the reason that the door won't open. Whether or not it will open after pulling the dent out depends on...

I have a 06 volvo s40 t 5 awd.it is leaking antifreeze from the drivers side direcrly underneath the transmission.runs great, no

Hello, thank you for writing in.The best way to determine the cause of the leak is to locate where it is coming from. There are several cooling system components in that area including hoses and the heater core. Both components...

My car shakes very bad whenever I'm accelerating or driving uphill...Could it be a motor mount or transmission issue?

Motor and transaxle mounts, or an engine operating condition such as misfiring, are likely causes. A fault in the transmission is a less likely cause of the shaking that you are describing. Motor mounts fail due to separation or tearing...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com