GMC Sierra 2500 HD Classic Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(98)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(98)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a GMC Sierra 2500 HD Classic Water Pump Replacement is $490 with $238 for parts and $252 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2007 GMC Sierra 2500 HD ClassicV8-6.0LService typeWater Pump ReplacementEstimate$918.04Shop/Dealer Price$1084.28 - $1568.42
2007 GMC Sierra 2500 HD ClassicV8-8.1LService typeWater Pump ReplacementEstimate$739.28Shop/Dealer Price$861.71 - $1221.56
Show example GMC Sierra 2500 HD Classic Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(98)

Rating Summary
97
0
0
0
1
97
0
0
0
1

Scott

39 years of experience
607 reviews
Scott
39 years of experience
GMC Sierra 2500 HD Classic V8-6.6L Turbo Diesel - Thermostat - Denver, Colorado
Scott did an excellent job. Would highly recommend his services.

Brandon

9 years of experience
133 reviews
Brandon
9 years of experience
GMC Sierra 2500 HD Classic V8-6.6L Turbo Diesel - Exterior Door Handle Replacement (Driver Side Front) - Gallatin, Tennessee
Very professional and done excellent work.

James

28 years of experience
25 reviews
James
28 years of experience
GMC Sierra 1500 V8-5.3L - Water Pump - Austin, Texas
Very knowledgeable and professional Great service

Scott

37 years of experience
995 reviews
Scott
37 years of experience
GMC Canyon L4-2.9L - Water Pump - Mesa, Arizona
An outstanding Mechanic with an Outstanding attitude. I will recommend Scott to friends when they need a mechanic.

Excellent Rating

(98)

Rating Summary
97
0
0
0
1
97
0
0
0
1
Number of GMC Water Pump Replacement services completed
1078+
services done by our mechanics
TOTAL NUMBER OF EXPERT GMC MECHANICS
900+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Fuel Pump Relay
If the engine is stalling or not starting, or the fuel pump is not making any noise when the key is on, you may need to replace the fuel pump relay.
How Long Does a Center Support Bearing Last?
The The center support bearing is normally on mid-size or heavy-duty vehicles, such as trucks. The purpose of this part is to help support the longer drive shaft that these vehicles depend on. The drive shaft is divided into two...
How to Transfer a Car Title in California
The The title to a car proves ownership. That’s true in California, and throughout the rest of the nation. If you are buying a car from a dealership, they will handle the transfer process and you don’t need to do...

Battery is fine but car won't turn over?

Hello, thanks for writing in about your Ford Fiesta. You need to check to see if the clutch starter interlock switch is making contact. If the clutch switch (https://www.yourmechanic.com/services/clutch-switch-replacement) is bad then you need to have it replaced. If you're...

Rough idle at stops lights and when parked

This may be a sign of a faulty MAP sensor. The Manifold Absolute Pressure (MAP) sensor senses engine load and generates a signal that is proportional to the amount of vacuum in the intake manifold. The engine computer then uses...

Got a p0340 code and replaced the camshaft sensor still going off checked voltage got the 5 volts trying to figure out what else could be causing the problem

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com