GMC Sierra 1500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC Sierra 1500 Brake Drum Replacement is $370 with $208 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2012 GMC Sierra 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$882.56	Shop/Dealer Price$1056.33 - $1521.39
2017 GMC Sierra 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.72 - $1023.61
2010 GMC Sierra 1500V8-6.0L Hybrid	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2019 GMC Sierra 1500V8-6.2L	Service typeBrake Drum Replacement	Estimate$577.64	Shop/Dealer Price$698.67 - $1023.54
2005 GMC Sierra 1500V6-4.3L	Service typeBrake Drum Replacement	Estimate$1014.54	Shop/Dealer Price$1216.06 - $1734.85
2014 GMC Sierra 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$804.86	Shop/Dealer Price$982.74 - $1478.05
2012 GMC Sierra 1500V8-4.8L	Service typeBrake Drum Replacement	Estimate$845.06	Shop/Dealer Price$1018.53 - $1483.37
2016 GMC Sierra 1500V8-6.2L	Service typeBrake Drum Replacement	Estimate$801.86	Shop/Dealer Price$977.27 - $1464.25

Show example GMC Sierra 1500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(340)

Rating Summary

312

14

6

0

8

312

14

6

0

8

SEE REVIEWS NEAR ME

William

14 years of experience

95 reviews

Request William

William

14 years of experience

Request William

by Ron M. Drey

Sierra 1500 2000 - Brake System Flush - Denver, CO

It's always great with Will.

Victor

0 years of experience

196 reviews

Victor

0 years of experience

by Pranab Shenoy

Sierra 1500 2004 - Wheel Hub Assembly - Albuquerque, NM

Victor is the best. He was able to diagnose the problem and fix it quickly. Victor is MyMechanic!

Victor

0 years of experience

196 reviews

Victor

0 years of experience

by Pranab Shenoy

Sierra 1500 2004 - Shock Absorber - Albuquerque, NM

Victor is the best. He was able to diagnose the problem and fix it quickly. Victor is MyMechanic!

Chuck

4 years of experience

271 reviews

Chuck

4 years of experience

by David Fletcher

Sierra 1500 2011 - Exterior Door Handle - Dallas, TX

He showed up early and got the job done quick. A+

Excellent Rating

(340)

Rating Summary

312

14

6

0

8

312

14

6

0

8

SEE REVIEWS NEAR ME

Recent articles & questions

4 Essential Things to Know About Cleaning the Interior of Your Car

Cleaning Cleaning the interior of your car is something that should be done regularly. It will keep the seats, carpeting, and overall condition of your vehicle looking better for longer. If you decide to resell it in the future, your...

The Guide to Right-of-Way Laws in South Dakota

If If vehicles or pedestrians are approaching one another, in the absence of signals or signs that can regulate the flow of traffic, right-of-way laws apply. Since most accidents occur as a result of failure to yield the right of...

P0348 OBD-II Trouble Code: Camshaft Position Sensor A Circuit High Input (Bank 2)

Trouble code P0348 means the voltage reading from the camshaft position sensor circuit for camshaft sensor A in engine bank 2 is too high.

2004 Chevrolet Monte Carlo won't stay running

Hello. Problems such as these can be caused by many things. Anything ranging from a bad vacuum leak, to a faulty idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) will cause symptoms such as these. As engine performance problems can many times be...

Car shuts off after sometime I start the engine!

A poor engine idle could be due to a faulty idle air controller or IAC for short. The IAC controls the engine idle speed by allowing more or less air into the intake manifold. More air equals high RPM, less...

How often tune up needed

Hi There, Your maintenance intervals can be found here: http://www.aboutautomobile.com/MaintenanceSchedule/2006/Infiniti/QX56, which will indicate the recommended service schedules for your vehicle. These will tend to vary based upon how many miles per month you drive. This will also vary in terms...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com